SRA22B Maytag Refrigerator - Instructions

Replace the refrigerator lightbulb while traveling 88 mph then turned on the flux capacitor being carful not to get stuck in a worm hole. This allows you to fix the problem before it starts to go bad.

First off, We have an extended warranty however, they said it was not coverered since it did not affect the function of the refrigerator (except that we lost refrigerator space and could no longer use that section of the fridge!!!) They said it was cosmetic!! After having a repair person come out and tell for the part and repair it would be $217.00.
I then got on line and looked up the part which with shipping cost us 37.00. My husband installed the part in no time.
Word of advice: make sure when you purchase warranties that you check the fine print ,because there are all different levels of warranty.

First we removed screws in the top hinge, then lifted the door up and off the bottom hinge. Replacement of the door closer and lower hinge pin took less than a couple of minutes. Then putting the door back on and screwing the top back on was nothing.

We additionally replaced the puriclean filter which simply was twisting it off and then the new one back on

1. Unplug refrigerator and remove fountain drip tray.
2. Remove the two #15 torx head screws that were covered by the drip tray.
3. Pull the bottom of the trim panel out and push up to remove panel and then unplug switch circuit board connector..
4.Remove the three screws (same size as the other two) and then remove the switch, ice door, etc assembly and unplug the connector.
5. Aside. At this time I extended the water hose which has been short since new. Used a couple of inches of 1/4 inch plastic tube. Heated it with boiling water and slipped it over the existing tube to extend it about 1/2 inch. Now the water flows in a uniform predictable stream.
6.Remove the tiny phillips screw holding the switch in place.
7.Remove and replace the old switch and actuator pad and screw. Check operation of switch. I lubricated the surface between the switch actuator bar and the rubber with a little plastilube(white) grease. Probably highly optional.
8.Replace and replug the assembley. Tuck the actuator pad around the edges if needed. Remember to turn the screws CCW until they fall into the old threads and then tighten them until snug.
9.Plug in and mount trim and connect refrigerator.

Simply cut the water tube on both sides of connector and push in the new one.

I watched your online video on how to take out the old filter, and then to replace it with the new filter. It was as easy as on the video. Thanks!

Once I identified the bit that would remove the screw, the rest of the repair took 5 minutes. I removed the screw and discarded the remains of the original but now broken shelf support. With the same screw I simply attached the new shelf support that I received from PartSelect.com. End of story.

Viewed the repair video. Removed covering. Replaced limit switch, control board, and solenoid. Very easy repair!

This replacement glass shelf arrived the very next day-after it was shipped. I was so impressed with the easy method of ordering and the prompt delivery of this product-also, the quality of the shelf was perfect. Great service!! I would recommend this for everything-as far as parts needed for repair or replacement.

removed three nuts from the top of the door diconected the electrical connections for the ice and water in the door. Removed door by lifting it up about 2 inches, set it aside put new hinge pieces in placed put everything back together. writing this took more time. wanted to add, bought at 2 pm on thursday was at my house by 10am the next day

At first I thought I had ordered the wrong bracket but all I had to do was push it up and pull down and it snapped right in place. If a 71 year old lady can do this any body can do it. Thank you for the fast service.

I removed the top refrigerator side hinge screws. The door came right off. Slipped in the lower hinge pin.. Unscrewed the natural door closer and replaced. Reinstalled the door. It is unfortunate that these parts are plastic. They wear out way too soon. No, the door is not over weighted. If you have no weight in the door the plastic shelves will hinder the door closing. Putting stuff on the shelves makes them take their proper form.

Removed the hinge cover on top and the 3 screws. Disconnected the electrical connection.
Lifted the door up from lower hinge and laid the down down on the floor. Carefully because there is a water line coming up through the lower hinge cup.
There is a Paraflex water connector so you can disconnect the water line and feed the line up through the cup. Having never seen one, i called, googled, etc. to find out how the connector was to come apart.
No one knew. No one!
I put the door back together and called Maytag only to find out that they do not provide technical service on any of their parts.
I was telling a friend of mine, who is an engineer,
about the dilemma. He came over and said it was a push-pull connector and he took it apart.
After that, I put the new parts in and put the door back on, Replaced the lower plastic hinge cover.
(Open the door first)
After swearing I would never buy another Maytag product, I fixed myself a drink (It was after 6:00 pm)
and relaxed.

After taking advice from the other posts, I removed all contents from the door, removed the screws from the top hinge and then lifted the door off the bottom hinge pin.

While door was lying flat I unscrewed the old natural closer, replaced it with the new one. Swapped out the old lower hinge pin with the new one.

I then had someone help me lift the door back on the hinge pin and fastened the top hinge screws while they held the door in place.

It worked perfectly and was very easy.

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.