All Installation Instructions for Hotpoint Range RGB790SEH2SA

Oven bake button would not work.

Simple swap and go.Several wires had different locations but every thing was marked well on both panels.Did one wire at a time.Took about 45min from pulling out oven to pushing back in.Just wish I had known about your site years ago.

Parts Used:

Gas Oven Electronic Control/Clock

Richard from LITTLE ROCK, AR
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Hard to remove screws & no instructions that a heat shield had to be transferred from old to new

One of the initial two screws for the oven bottom would not budge. Finally used a socket set to loosen it up. Upon taking out the old bottom I turned it over & saw a heat shield attached. I have no idea if you can order a new bottom with a new shield already attached or not, but I had no idea it was there until I took the old part out. Out of the eight screws attaching the shied, four of them were also difficult to loosen up. But in the end the new bottom looks great !

Parts Used:

BOTTOM OVEN AND DEFLECTOR ASM

Peter from REDDING, CT
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

No oven

Hired gas company to do repairs for safety reasons

Parts Used:

LP Conversion Kit

Robert from SAUGERTIES, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench (Adjustable)

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

main controll panel quit operating oven

bought new panel and installed and looking @ wire connections from old control, I'm very much mechanically inclined , so was a breeze for me, but non handy people may not know how to disassemble the control panel without not having an idea how it's made. I'm a "mr fix it", "jack of all trades" kinda guy and am proud of it.

Parts Used:

Gas Oven Electronic Control/Clock

Jim from muskegon, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Well used burners..

Replaced the old with the new parts...stove like new...very pleased with the improved function and appearance of stove.

Parts Used:

Small Burner - 5K

Burner Head - Medium - 9500

Burner Head - Large - 12K

Double Burner Pan - Left Side

Melissa from Mastic Beach, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 16 people found this instruction helpful.

Was this instruction helpful to you?

Oven would not come up to temp/retain at temp

Very simple repair, removed the back plate, took off the 4 screws holding the controler panel on, swapped over the wires one at a time, and reinstalled. Less than 15 min total time.

Parts Used:

Gas Oven Electronic Control/Clock

Ken from Painted Post, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

The light inside the oven had burned out

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Parts Used:

Light Bulb - 40W

Catherine from SEATTLE, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

The eye would not light

Remove the existing burner and install the replacement.

Parts Used:

Burner Head - Large - 12K

Solomon A from COLLEGE PARK, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Burner had uneven flames

Too easy a five year old could do it

Parts Used:

Burner Head - Large - 12K

Akshay from Bridgeton, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Uneven flame on large gas burner

The part was very easy to switch out but it made no difference whatsoever so I returned it. The way it is designed is the problem. There is a pie slice shaped gap on the burner which causes a gap of no flame. Also a C shaped cut out around the igniter which causes another no flame gap.

Parts Used:

Burner Head - Large - 12K