All Installation Instructions for Hotpoint Range RGB745BEH2CT

Burner on stove not working correctly

Order parts and installed - no tools needed - completed repairs less than 1 minute

Parts Used:

Burner Head - Medium - 9500

Trevor from Eldersburg, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Symtoms: a fluttering noise was heard for a few weeks in the oven prior to it not working at all.

When turning on the oven, I could see the ignitor red hot but it would not ignite the burner. I ordered the pair of new ignitor and burner tube. Upon removal of the burner tube, I saw a large hole in the tube where the center of the ignitor is located, clearly in need of replacement. Unlike some other ovens, the connector on the new ignitor was the exact fit for my oven (Hotpoint RGB745BEA7WH). After access to the tube, the replacement took less than 10 minutes not including watching about 3 youtube videos on how to actually do the replacement prior. You should turn the gas and electric off but ooops, I forgot. I was shocked at how easy this was!

Parts Used:

Burner with Igniter

James from WEBSTER, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

oven would glow but the burner would not come on

My son took out the old burner bar and there was a hole burnt right through it. I ordered the part on Weds night and was surprised when we received it so quickly on Fri morning. He had no trouble at all - just removed the old igniter and bar and replaced it with the new one. Nothing needed cut or spliced - perfect match. Now I can bake again!!!

Parts Used:

Burner with Igniter

Charlotte from Rochester, PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

7 of 15 people found this instruction helpful.

Was this instruction helpful to you?

none

slid the old ones out and slid the new ones in. done

Parts Used:

Oven Rack

Michael from Laughlin, NV
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Drawer glide broken

took nut driver to remove the old and replaced with new. simple.

Parts Used:

Drawer Glider - Right Side

TERESA from SALTVILLE, VA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Gas range igniter was making a clicking sound every 3 to 5 minutes, as if it was trying to ignite one of the burners.

Unplug the range from its wall socket to avoid electric shock. The various range parts that support a pot or frypan are easily lifted off their perches, exposing the small white igniter. The only moderately difficult aspect is wiggling the igniter out of its retainer. The electric wire leading into it then can be pulled out and fed into the new igniter with a push. Replace igniter in its retainer, then replace the range parts you removed to expose the igniter and plug the range back into the wall socket. Piece of cake.

Parts Used:

Top Burner Spark Electrode

Wesley from FRANKLIN, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Neither oven nor broiler burner would light, no gas coming from burner.

Remove the warming drawer entirely. Remove all five nuts securing the valve and regulator assembly. Loosen (do not remove the nuts entirely) the burner assembly itself to give some wiggle room above the valve and regulator assembly. Also remove the single screw that holds the "collar" in place just above the gas outlet that services the oven burner. This should provide the margin of room you need to remove the valve and regulator assembly because it's a tight space. Working entirely in this cramped space (the warming drawer) will take time and patience. Don't drop any screws because you might create a whole load of more work for yourself. Loosen the brass nuts holding the gas lines in place. Then you have to maneovre the old equipment out. Just reverse all the steps to install the new equipment. Apply Harvey's to the brass nuts and re-attach the gas lines BEFORE you firmly attach the equipment using the five nuts. Don't tighten the brass parts all the way, just hand tight at first. Re-attach the equipment using the five nuts, then tighten up the brass parts with a wrench. Don't over tighten. Re-secure the screws that hold the burner in place. Then test the equipment. If all good, wait for the oven to cool, then do a final check that all the screws are firmly in place. Voila.

Parts Used:

Safety Valve and Regulator Assembly

Michael from Chicago, IL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Oven bake button would not work.

Simple swap and go.Several wires had different locations but every thing was marked well on both panels.Did one wire at a time.Took about 45min from pulling out oven to pushing back in.Just wish I had known about your site years ago.

Parts Used:

Gas Oven Electronic Control/Clock

Richard from LITTLE ROCK, AR
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

No oven

Hired gas company to do repairs for safety reasons

Parts Used:

LP Conversion Kit

Robert from SAUGERTIES, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench (Adjustable)

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Hard to remove screws & no instructions that a heat shield had to be transferred from old to new

One of the initial two screws for the oven bottom would not budge. Finally used a socket set to loosen it up. Upon taking out the old bottom I turned it over & saw a heat shield attached. I have no idea if you can order a new bottom with a new shield already attached or not, but I had no idea it was there until I took the old part out. Out of the eight screws attaching the shied, four of them were also difficult to loosen up. But in the end the new bottom looks great !

Parts Used:

BOTTOM OVEN AND DEFLECTOR ASM

Peter from REDDING, CT
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Oven would not come up to temp/retain at temp

Very simple repair, removed the back plate, took off the 4 screws holding the controler panel on, swapped over the wires one at a time, and reinstalled. Less than 15 min total time.

Parts Used:

Gas Oven Electronic Control/Clock

Ken from Painted Post, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

main controll panel quit operating oven

bought new panel and installed and looking @ wire connections from old control, I'm very much mechanically inclined , so was a breeze for me, but non handy people may not know how to disassemble the control panel without not having an idea how it's made. I'm a "mr fix it", "jack of all trades" kinda guy and am proud of it.

Parts Used:

Gas Oven Electronic Control/Clock