RF366PXDN0 Whirlpool Range - Instructions

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Turn off power to the stove (unplug or turn off breaker)
Remove back panel screws (Phillips) and back panel
Unplug switch
Remove knob and attaching screws (Phillips)
Remove and replace switch
Reinstall screws for switch and plugs in the back
Snap off the end of the stem if it's too long and reinstall knob
Reinstall back panel and turn power back on

*important: the large element has an updated switch and you may need to snap off the end of the stem with pliers! It's too long and there are no instructions for this included!*

I read other other posts and followed their advice. Remove the 2 screws holding the element to the back of the oven...gently pull it out about 3" to reveal the connecting wires. I found the needle nose pliers were necessary to detach and reattach the wires. Don't yank! Be aware that the wires have a tendency to want to pull back into the back of the oven while they're loose. This was a wall oven and that woul've been a large problem if they they had. Otherwise it was a snap!

First, I turned the breaker off to the oven, that's the most important step.
Next, I turned on the oven to make sure the oven was not energized.
I then took out two phillips screws that were holding the baking element in place.
Next I pulled the element out slowly to expose the wires that connected to the element.
I removed the connecters, took out the damaged element, replaced it with the new element.
Last, I screwed the two phillips screws back in, and saved a $65.00 service call.

pull range from slot in cabinets, remove power cord from wall plug, remove cover from control panel, hold new control next to old one and transfer wires from one to the other one at a time; reverse procedure to get things put back together

First I turned off the circuit breaker to the oven. Then, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches to disconnect the two wires. The connectors were tight, so required a little wiggling to disconnect the wires.

Upon receipt of the replacement element, I turned off the circuit breaker to the oven. Then, I reconnected the element wires, pushed the connect wires into the back of the oven, and rescrewed the unit in place. With the circuit breaker turned back on, I tested the oven. It worked great. Very easy!

I decided NOT to crawl under my stove top to find the correct model no. of the unit, as recommended in the Help section of the website. Instead I just guessed. It arrived, and of course didn;t fit. So I crawled under the stove top, got the correct model no., and instantly found the correct part to order. Part Select instantly honored my request for a refund on the first part and the correct part is on its way. So I ended up paying two delivery charges instead of one. LESSON LEARNED.

Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.

Was able to use a philips screwdriver and remove 2 screws. I then clean the bottom of the oven. The installation was even easier. Took less than 5 minutes. Saved over $60.00 in labor cost

Removed the 2 screws that hold the element in place. Pulled the element forward about 3 inches and disconnected the two wires. Plugged the wire clips onto the new element and pushed the element back into place. Put the 2 screws back into place. This was a very easy repair.

I had to pull the stove out from the wall and discounted the power source from the wall. Than I used the a phillips screwdriver take out the heat element. There was now problem fixing the stove. Lowell Moxley

Remove racks, extract two phillips head screws, pull out element, unattached wires, install new element, reverse procedure to complete installation. (Note: With the racks and element out, great time to clean oven.)

Just like you said,remove two screws,pull out element,disconnect wires,install new part. It was easier to pull out stove and hook up wires.

Naturally the oven turned was off but for added safety I also set the breaker protecting the oven to the off position. Where the element attaches to the oven there is a small plate with two screws holding the element in position. Remove these two screws and then gently pull the element out 2-3 inches, which will expose the electrical connection. Using needle nose pliers gently pull on one of the wires to remove it from the element. Now remove the other and discard the old element. Simply plug the new element into those wires and screw the plate back into the oven. Now turn the breaker back on and you're done. Super easy!

I removed two screws, pulled it out a few inched and unpluged two wires. I then plugged the two wires into the new element slowly slid the wires and element back into place and put the two screws back in... and it worked perfectly. I did it all in less than five mins. And I am a 53 year old woman.No man was required.