PTC22MFMRB General Electric Refrigerator - Instructions

unplugged refrigerator. removed light bulb from old socket. unsnapped old light socket and pulled it out just enough to diconnect the electrical plug that plugs into the socket . discarded the old socket and plugged in new socket. snapped in new socket into refrigerator. i watched how to do this simple procedure on you tube and decided to do it myself. easy easy easy

Unplug the refrigerator
Front cover of ice dispenser snaps off. Remove the 4 screws from the ice chute. Unplug the control module that opens the ice chute. Leave hanging while removing the 4 screws that hold the solenoid in place.(one is a ground wire...note location before taking apart). Unplug the two wires to the solenoid.
To install the new solenoid put the plunger in place and at the same time hook on the trip arm of the clapper door of the ice chute. Plug in the two wires to the new solenoid
Replace the 4 screws.
Plug in the Control modules and screw back in place
Plug in the refrigerator. Do a trial test.
Replace the cover

Removed the ice bin and maker, then removed cover from the rear that covered the solenoid that controls the dispensing mechanism. Replace solenoid. The tricky part here is that there is a styrofoam cover around the solenoid pin that needs to be superglued into place and oriented properly during replacement. All electrical feeds snap out neatly and are easily replaced. Reassemble ice dispenser and bin, and viola, your back in business.

I had noticed water on the front left of the fridge on the floor.I thought it was the drain in the freezer so i poured hot water with baking soda into the drain but it didn't help..I pulled the fridge out and saw water dripping from the water valve solenoid.I searched the web for parts and found Parts select.com.I found the part quickly and they had pictures from all angles to assure me that it was the exact part which was great.The transaction on line was simple and the part came the next day.I will definitly use this sight again

Used by pass filter and problem disappeared. Of course wayer is now unfiltered. This is a GE design flaw. Also replacement filters are outrageously expensive and do not last long. We have good water here and I'll stick with the bypass.

Unplugged frig. Turned off water supply to pump. Removed black cardboard covering on back of frig with nut driver (6 screws).

Took digital photo of assembly to confirm reassembly position.

Removed copper waterline to pump with adjustable wrench. Removed 1 screw holding pump assembly to refrigerator. Pulled assembly out of the frig. Unscrewed two small black screws on a second bracket. Pulled old pump further out of frig. Unplugged two connectors. Removed plastic waterline from pump by turning hose counter-clockwise and gently pulling.

Inserted plastic water line into new pump by turning line in clockwise and it pushing into orange plastic stop. Reconnected two electrical connectors. Reconnected bracket to pump with two small black screws. Gently pushed assembly back into the frig and reconnected pump assembly to the frig with 1 screw. Reconnected copper water line to pump first wrapping threads on pump with Teflon plumbers tape.

Turned on water to check for leaks. Installed cardboard back on frig with 6 screws. Plugged in frig.

NOTE. My new pump assembly had the electrical connectors reversed. Take care to pair up the correct colored connectors.

I checked the compressor and it was running. Next I removed the doors amd screws that held the divider strip. Next removed the bottom of the freezer to expose the evaporator fan. Removed the fan and checked it out with volt ohm meter. Discovered the fan motor was out. Ordered new one on line and received thenext delivery day. Insatlled in reverse of disassembly. When I plugged it in everything worked fine. Thanks for the quick delivery. You provided fine service.
Sincerely,
Joe Sutphen

Unplugged refrigerator from electrical outlet for safety and turned off water supply valve. Removed the four metal screws that hold the access cover on the rear of the refrigerator. Then removed single metal screw attaching water valve and bracket assembly. Unplugged wire harness from the water valve and assembly then pressed down on colored o-rings to detach the four plastic water lines from the water valves. Used open end wrench to disconnect main water supply line from the water valve.
Pressed down on colored O-rings to install the four plastic water lines to new water valve and bracket assembly. Wrapped plumbing tape on threads of inlet valve and and used open end wrench to attach main water supply line to new water valve and bracket assembly. Attached wiring harness to new water valve and bracket assembly. Mounted new assembly to refrigerator with single metal screw. Turned on water supply valve and checked for leaks. Plugged in refrigerator to electrical outlet and tested water dispenser. Replaced access cover on rear of refrigerator with four mounting screws.

Removed the face plate this just gets popped off. removed the four screws to release the unit. unplugged the wiring harness, removed the two screws that hold the bracket in place that the control unit is housed in. Slid the old unit out and replaced with the new unit. installed the bracket over the control unit put two screws back, plugged the wiring harness's back in. Slid the whole unit back in replaced the four screws and put the face plate back on. Very Easy.

The leak was obvious and I took out the cardboard backing. I closed the valve (water supply) to the water dispenser and ice maker.

With the screw drivers and socket set, I was able to take out the old valve and disconnect the hoses.

Since the part was identical to the leaky valve it was just a matter of reversing the steps. I had previously researched on the web to find the identical part and found a match at Partselect.com. I wish all my repair attempts turn out to be this easy. I wish GE had used better parts since this incident has set me back by several thousand dollars due to the water damage to the wooden floors, basement ceiling and walls.

Isolated water line. Remove water valve from harness. Disconnect water connections. Disconnect electrical connections. Removed valve. Installed new part. Reconnected water connections and electrical connections. Opened water line.

unscrewed old filter by hand, installed new filter.

On one severe winter cold night my fridge dispenser door stopped water supply, but ice maker was working. First I disconnected power supply to the fridge then turned off main water supply from the wall to fridge and with wrench set disconnected water supply pipe from wall to fridge while disconnecting the pipe make sure to collect the water from the both end pipes. Then removed the cardboard from the back side of the fridge. I disconnected the blue element (dispenser water) the red element (ice maker). [DOUBLE OUTLET WATER VALVE]. If you would try to pull the pipes white (dispenser water) and black (ice maker) you woudn't succeed because once the the white and black pipes are insereted into the water valve those pipes are clamped tightly in the valve. So I cut off those pipes and removed the old water valve, then I conncected the new water valve first conncected those white and blue elements and inserted the white and black pipes pushed in closed with round plactic caps comes with new one.I reconncected the main water supply pipes from wall to the frige and turned on the water supply from wall and plugged the power supply. First surpisingly I doubted it will work, actullay the water dispnser did'nt work immediately I have to wait 2 to 3 hours of time, in the mean time I checked the pipe connections from the bottom of the front left side door ( if you open the two doors bottom you can see the plastic cover it can be removed by pulling towards and pushing in you can close it back into normal position) which water supply pipe comes through the bottom of the door to water dispenser. I disconnected the connector and pusheed the dispensor several times to flushout any leaky water or air then I reconnected the pipes to the connector. I pushed the dispenser with a cup to dispenser, it started working as it is normally. While I was working my 7 years old son helped me as he always eager to learn and explore things.

Called partselect and gave my model number for the frig. I wanted a filter plug because we did not need a frig filter. We have a whole house filter. They looked up the part, took my info, and sent it to me by UPS. It arrived fairly quickly and fit the frig perfectly. I screwed it into place immediately. It was the simplest order I have ever placed and the salesman was very pleasant and proficient. If I have more issues with my frig, I will call partselect again. Just remember to turn off the water before you start.

First I removed the face plate by lightly prying . Once removed noticed 4 screws. Removing the screws allows you to gain access to the two plugs, one for the solenoid and the other for the switch that energizes the solenoid . Unplug the connectors and carefully lower the piece enough to reach the 3 screws that hold the solenoid in place. The 4th screw in the center at the bottom of the solenoid is the ground wire. If it is rusted like mine was just re-attatch it to one of the solenoids holding screw. It must be grounded!
Just re-assemble, just dont forget to replug the connectors. Also a little hint, If you open the freezer door a little you wont trigger the solenoid.