PSG22SIPCFBS General Electric Refrigerator - Instructions

Part arrived very fast as ordered..need to pry old switch out from top..use care to push the retainer down..after old switch was 1/2 out, I used a putty knife for better leveridge.Remove wire connector...after plugging in the wire connector to the replacement switch, make sure the switch is properly positioned so the switch will depress when door shuts.

This repair was very simple to do. I cannot say enough about part select dot com. I feel that I am a definite handy man yet the videos on the part select dot com site proved to be valuable. This video showed and reminded me that the plastic bushing holding the auger on was reverse threaded. Being a rightee tightee leftee loossee person embedded in my head I would have worn out that bushing holding the auger in place. I recommend not only purchasing from partselect.com YET please watch the video on this site prior to this installation. This made the installation not only simple yet informative. Thanks!

Replaced flapper

My GE refrigerator emitted high pitch noise a short while ago. I tried different dampening methods that helped but not eliminating the problem. I finally replaced the fan, motor, and associated parts and solved the problem. The total cost was about $50.

look very carefully at the picture you provided in the parts fish, removed the ice maker tray and the rest was very easy ,i saved alot of money and time doing it myself.

i used the video it showed on the site or iwould not have been able to do it

Remove lower front panel, disconnect damaged union from water hose under freezer door, replace with new union, tighten and reattach front panel. No more water coming from under the unit. Ice maker and dispenser features returned to working order!

I recieved the new ice bucket, I took out the old ice bucket and put the new ice bucket in.

I replaced that part, but I still have the same problem, no water is dispensed. I believe I may need a circuit board. The problem was not the parts I replaced.

I downloaded a schematic of the ice dispensing unit. The whole unit pulls out and there are a couple of screws that remove plastic covers. The "trick" was to get the two plastic tabs pushed in and lift the auger unit out of the tray - a two person job! We used knife blades (it was the thinist and strongest tool around) to push the tabs in and pry the auger assembly out. I think we did a great job NOT breaking the plastic pieces! As careful as I was, I definately needed the schematic to put the ice crushing blades and spacers back together. All of this could be avoided if they used a metal auger instead of plastic!

Part arrived in 2 days and took about 15 seconds to install. Great!! No more broken eggs!!

as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapped the new switch into place.

10 minutes total.

A second person is necessary to help prop up the refrigerator. One person will need to insert a 6 inch support under the front of the refrigerator base while another person rocks the refrigerator back to provide access for the support to be inserted.

The front refrigerator panel was removed to reveal the refrigerator base and provide access to the front wheel assembly adjustment screw (screw mobility). The front of the refrigerator was propped up on a solid support about 6 inches above the floor to provide access to the front wheel assembly and allow removal through the base of the refrigerator. The front wheel assembly was dislodged from the base by first removing the pivot pin by hand and then prying the wheel assembly loose with a screwdriver. Normally the pivot pin would need to be released by prying it loose with a screwdriver and then pulling to free by hand. Once the front wheel assembly was dislodged the adjustment screw was removed with a socket set and the front wheel assembly fell out of the refrigerator base. The new front wheel assembly was then inserted into the refrigerator base, the new pivot pin was inserted and aligned with the support holes and pressed into place to secure with locking mechanism. The new adjustment screw was then inserted into the refrigerator base hole, aligned with the front wheel assembly and hand tightened to set the first threads. The adjustment screw was then tightened with a socket set to seat the adjustment screw. The refrigerator was then lowered and the adjustment screw was adjusted to level the refrigerator. The refrigerator was then pushed back into its normal position and a final adjustment performed to assure the refrigerator was level. The front refrigerator panel was then pressed back into place.

Ice maker assembly removed from refrigerator and disassembled. Note nylon nut holding the Augur in place is removed clockwise. As you take the assembly apart, note each piece for reassembly.

I am 85 years old and had no trouble replacing the Augar. Removed ice maker from frig. Remover the ice shield (one screw, remove front panel (2 screws) carefully removed augar assy.

Removed the lock washer,the the end plastic nut, being careful in removing the ice crusher blades. Replaced the augar and all parts. Checked out the ice dispenser and the crusher, both worked fine