This OEM ice and water filter fits side-by-side and bottom-freezer GE models. The most common reason you would need to change this part is if you have never updated your model and it is no longer filt...
This is a replacement spring pin for French door-style refrigerators. This part is made of white plastic and is approximately ½ an inch in length. If the mullion that keeps the doors closed is not wor...
This is the replacement pantry flip lid cover for your refrigerator. It is made of clear and white plastic and is approximately 30 inches in width and 6 inches in length. The pantry flip lid cover is ...
This part is the replacement French door hinge for your refrigerator. It is made of white plastic and is approximately 1 ¼ inch by 1 inch. The French door hinge can also be known as the flipper hinge....
This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sandy
January 22, 2020
It won't cool or freeze. The circuit board was jiggled and it started to cool and freeze for a couple of days, then warmed up again. The circuit board was replaced but then the fan and compressor would not turn on. Told it was the compressor. Could it be the start relay switch or something else?
For model number PFSS6PKXASS
Hello and thank you for writing.
Yes, it could be the compressor start relay PS2322852, you should check the part(s) for signs of damage, and replace as necessary. We hope this helps. Please contact us anytime if you require further assistance.
Hello Jerry,
Thank you for your question. Unplug the fridge, then remove the shelves to gain access to the back panel to remove the screws out so you can gently pull the panel out. There are 2 wire connections in the upper right corner, so disconnect the wires making sure you take pictures of how they were connected, then remove the 4 screws holding the metal fan panel in place. When its removed, twist the fan 90 degrees and it will be free, and a spring clip that holds the fan blades on the motor will need to be removed. Use a pair of needle hose pillars to pull the spring clip off, then finally pull the fan blade off the motor. Reverse the process for re installation. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Leroy
August 3, 2021
Does not mak ice there’s water flow but no ice it’s on unlock mode i just recently changed filter
Help
For model number PFSS6PKXASS
Hi Leroy,
Thank you for your question. If you have just replaced the water filter, it is important to flush the water filter before using it. Also check the lines that provide water to the ice maker to see if they have an ice blockage. If you have already done this, there are some parts that you will need to check to see which one is causing the issue. You will need to check the ice maker assembly, the water inlet valve and the ice bucket assembly with auger. We hope this helps! Good luck with the repair!
my fridge is leaking water in the bottom under the long drawer, how can I find the leak? Please help
For model number PFSS6PKXASS
Hello JoAnn, Thank you for your inquiry. The most common causes of the refrigerator leaking water are the water filter, the filter housing and the water inlet valve. To check the water filter head and water inlet valve, first unplug the refrigerator and turn off the water supply. Remove lower cover of the back compartment. This will expose the water valve. Once you have valve exposed you will disconnect the water supply line and line to the valve. Once this is done, there is a cover at the top of the refrigerator where the lines go into the cabinet. Remove cover then go to the front of unit. With doors open remove the filter and cover over the filter head. Once removed there will be a 1/4 " screw holding the filter head in place. You can now check the valve, water tubing and the water filter head for any leaks. Good luck with your repair.
Hi Steve, thank you for your question. It sounds like you are looking for your mullion. That would be this part: PS2322804. Good luck with your repair.
Unscrew old filter and remove(counterclockwise). Line up arrow on new filter with arrow on connection housing. Turn clockwise till resistance met. Do not overtighten. Follow directions. Simple.
First, I have to say I live in the next state over, and I recieved the parts the next day. Yeah! OK, I removed the adjacent drawers *and the removable lower storage shelves on the doors for clearance*. Taking out the broken lid is easy. The new one is a tight fit. The right side has a raised pad on the pivot point, but the left one does not. I worked the peg (pivot point) in on the right side and slowly and carefully pushed the stationary plastic left side in slightly(and sprung the lid slightly) to get enough clearance to get in the left peg without breaking the new lid pivot. While doing this, one has to make sure the shelf immediately behind the lid is in place since there are support tabs located on it, and you will have to rework the thing if you don't get them to mate on the installation.
With our Fix app model plate image recognition technology, we'll recommend the parts guaranteed to fit your appliance. Simply snap a photo, and we'll take care of the rest.
"I love love love this app. It's so nice to have useful information (receipts, manuals, parts lists, warranty info, pictures, etc.) on all of my household appliances and devices in one place."
You added to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout