PDWT480R10SS General Electric Dishwasher - Instructions

I watched the video that came with email on part. Gave instructions on how to. Thank you !

Ordered most likely part...water inlet valve.

1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.

followed the video step by step which was very well expalined and was able to complete the install

Access to the parts was easy. Simply remove the outer door cover.

The only problem was that I had to disassemble and reassemble the dishwasher two times. Other than that, the actual repair was very simple; remove the old, replace with new and test with the built in diagnostic.

Put new basket in, threw old one away

pulled the end caps, pulled the upper dish rack out. Installed the rear end cap on the right hand side of the inside slider for the rack. installed the bearing and slider in position. Put the upper rack back in and installed the front end caps.

The Lower Rack was a simple swap. The Upper Rack had a tube and rotating sprayer that had to be removed and installed on the new rack. I used a nutdriver to remove a few screws and reinstall them on the new unit. Very simple.

went online to parts select. Looked at parts that could be leaking. Thought it was the sump. Purchased the sump and the pump connector. Almost bought the adaptor pump assembly, but it was $29.00. Parts arrived in about 2 days. Turned off water and power to dishwasher. Disconnected the copper water line. Hardest part was getting the dishwasher out of space. Once out, layed it on it's side. Parts held together with clamps. Took it apart like a puzzle. Replaced the parts, tightened the clamps. Pump connector hard to unscrew. Got a good hand grip on it and turned it loose. Sump did have a hole in it. Put everything back together. water, electric, etc. Turned it on and it was leaking. Leak coming from the adaptor pump assembly. Couldn't wait 2 more days.Found part at a local parts store for $40.00. Was able to change it by reaching underneath and not pulling dishwasher out again. All three parts needed to be changed. Dishwasher now working fine. If your leaking underneath and taking out the dishwasher change those 3 parts.

This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.

Simple install- just roll it in. Fit perfect. Better design than OEM part. Perfect.

I placed the missing cap into the dispenser.

It was a very simple replacement. I took the old one out and rolled the new one in. It took less than 5 minutes!

1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!

Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook

Slid it in. Very easy and the replacement part is built better than the original part.