NT2139 Refrigerator - Instructions

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

All I had to do was to screw timer knob back on threaded spindle. It took less than a minute to put it on. Easy! Thanks so much for easy find on your website. A HAPPY CUSTOMER FOR LIFE! Will keep all my old appliances! B. Paul

Made sure the threads lined up with the screw post. Turned the knob clockwise around the post because it was too hard to lift the washer and turn it. Kept turning until I couldn't turn it anymore. Done. Easy peasy, no need to call my husband.

Looked up on the internet and found the part. The Kenmore washing mahine is 20 years old. I have never had any repairs. The part came in 3 days and I merely followed the old threads on the screw and it washing machine works now!
I'm 77.
THANK YOU!

figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket

First I replaced the broken plastic control knob with the better die cast knob.
Pried the cap from the top of agitator assembly ..after first removing the softener dispenser.
Used socket with extender to remove visible retaining bolt. Pulled out plastic column and old dog bone ratchet assembly. Removed and replaced bottom spacer ( this had busted tabs and caused noise during agitation), greased all appropriate points with silicon grease..lithium would have been better...ordered wrong agitator so put old undamaged one back with new dogs which fit. Snugged down bolt..runs like new machine again.

I had already disassembled the part. All I had to do was thread the new part. My wife thinks I'm a genius. I guess I am, I ordered the right part and it was delivered in a timely manner.

removed old and instaslled new. biggest problem was getting to one of the screws.

I was happy to find this place. Sears was out of stock on this part. PartSelect was $5 cheaper than Sears and sent it the next day.

Part is better, inside is metal not plastic, won't break again.

Screwed off remains of broken plastic and screwed on new knob. Easy as pie!

I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.

I tilted the unit back enough to scew the new legs into the threaded holes.

I removed the 2 crisper drawers and the glass shelf directly above the Pantry Drawer. Removed the Pantry Drawer and Pantry Drawer cover so you have easy access to the Right-Hand End Cap. On the right-hand End Cap, there are 2 screws which hold the End Cap in place, use a 1/4 inch driver to unscrew the screws from the front of the cabinet on the End Cap and half-way in of the cabinet, leave the screws in their holes in the End Cap. Lift gently to get off a small plastic pin, and move the End Cap away from the Cabinet. You don't need to completely pull the End Cap out of the cabinet, it'll move more like a door opening. Place 2 washers on each screw and gently put the End Cap back into place, being careful NOT to jostle too much so the washers don't fall off the screws. You will need to gently lift the End Cap back in to place over the plastic pin. Hand-tighten the screws back into place with the 1/4 in driver. Remount the Pantry Drawer on the sliders. When you go to install the Pantry Drawer Cover, you will need to gently push on one of the pins to get the cover back into place. Put glass and crisper drawers back into place.

Test by gently pulling on the Pantry Drawer. If properly mounted, the pins will extend fully into the Cover and will keep it secure when opening the Pantry Drawer.

My wife wanted to call a repairman from the store. Instead, I ordered from PartSelect, replaced it in seconds, and saved over $100, all for about $20 - you can't beat that!