Quick Question!

Have you ever purchased from PartSelect.com before?

Models > NT2139

NT2139 (3G60A) Admiral Refrigerator - Overview

Get Parts and Repair Help for NT2139

If you know the refrigerator repair part you need, you can browse the list of all parts on the NT2139, or you can search by name or part description. You can also find your part by where it is located on the NT2139 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for NT2139 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$37.73

Condenser Fan Motor Kit

This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling t...

$8.52

Tray

This fourteen cube ice cube tray is eleven inches long. It is all white in color and is made entirely of plastic.

$69.02

Evaporator Fan Motor - 115V 60Hz - Blade NOT Included

This is an evaporator fan motor for a refrigerator. The fan motor circulates air through the refrigerator to the fresh food compartment for efficient cooling. It is just over three...

$33.77

6-Hour Defrost Timer

This part may appear different than the original, but will function the same. This device acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater.

$4.88

Screw

Sold individually.

$13.54

Hinge Pin Bushing

This bushing is used with a 1/4-inch pin. This part is found in refrigerators (and sometimes freezers). The bushing provides a bearing surface for the hinge pin that rotates. Every time you are opening and closing your fridge, this part is acting as a bearing and makes it so that the door is swinging back and forth with ease. This bushing tends to wear down over time and will need to be replaced. You will notice that this part needs to be replaced if your door is off-kilter and not aligned properly. This part is sold separately. This is a genuine part sourced from the manufacturer directly.

$9.38

Butter Dish

$17.15

Drier (Service)

This drier may also be known as a refrigerator ultra-violet dye drier or a filter drier and is meant to be used with your fridge. This piece is a filter for the refrigerant that moves through the refrigerators sealed-system. The most common reason you will need to replace the filter is if your fridge/freezer is not starting. You should consider having this piece installed by an appliance repair technician that is trained and licensed. Installing this part requires specialized knowledge and tools. The installation will require the service technician to recover and recharge the refrigerant in the refrigerators sealed-system.

$11.93

LEVELER

$5.50

Door Hinge Washer

This is a door hinge washer and is used in conjunction with your refrigerator. This part is just under an inch in diameter, it is all white in color, and it is made entirely of plastic. Making this installation should only require a 3/8 nut driver. The reason for needing to replace this part is if it is broken/cracked, missing, if you hear odd sounds when you open/close your refrigerator door, or your door is out of alignment. The hinge washer is located within the hinge assembly in the corner of your door. You will need to remove the door to make this repair.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 141 of 153 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

noisy fan motor

  • Customer: robert from nashotah, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 26 of 31 people found this instruction helpful
rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, close up, reverse pan... read more

Refrigerator stopped cooling. Pulled it out of the alcove and plugged it back in. Compressor starfted but noticed condenser fan was not turning. Unplugged fridge and tried to turn the fan by hand - frozen.

  • Customer: Florentino from Windsor Locks, CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 21 of 27 people found this instruction helpful
Remove the back hardboard cover screws for access to the condenser fan. I opted to tip the fridge over on its side for even better access to the fan mounts and wire. Replaced the fan assy (reused the fan). Splice the wire and it's done. read more