NT2139 Refrigerator - Instructions

Unplug
Remove entire back panel (both chipboard and metal fan grill)
Unscrew both fan mount plate screws - fan won't be able to come out because it is still plugged in
When looking at back of fridge, locate a small plastic box to the immediate left of the condenser. It's a circuit block. Release the metal spring clip holding the plastic cover in place, and trace the fan wire connections back to the fan. Make a note of which wire is connected to which terminal (1 of the fan wires has white lettering and 1 is just black)
Unplug both fan wire connects from circuit block to release the fan power cable.
Remove the fan mounting plate
Release fan blade clip by pressing fan against motor and unscrewing and remove fan blades
Unscrew motor from brackets - note alignment of motor on brackets
Mount new motor on brackets. Leave plug wire disconnected (replacement motor has a harnessed plug wire)
Connect new plug wire to the circuit block keeping wires connected to the proper terminals
Snake new plug wire behind condenser like the old wire was and run through cable bracket to the back right of the condenser
Plug wire harness into motor and re-mount fan mount plate
Reattach fan blade and secure using blade mount kit
Replace back panels

simply removed old motor and replaced new. I'm over 82 and it was hard to get down and up to floor level!! One thing was a little puzeling -that was to insert the right screws which had a nitch in the end of the threds to keep it from loosening- I thought I was spoiling the threds cause I had to use a little pressure to start the screws and thought I had the wrong screws--they had sent several sets of them for different name brands- but II got it and everything seems to be allright - Could you tell me if I could purchase a replacement compressor and some refrigerent -the new kind. thank you, George Erlandson Only if my comp. goes out!!!

Removed everything from inside freezer compartment (food and shelves) Removed inside backpanel that covered the coils. At the top of the coils is where the thermostat was attached. Removed old one and installed new. Has been working since.

Unscrewed the remains of the broken knob, and replaced it witrh the new one from you guys. Your service is great. Thanks.

Unable to get information from Part Select on how to use the part that they sent. Part had no grooves. Part Select people were very nice and offered refund but I got the directions from somewhere else. Used needlenose pliers to hold timer shaft and remove the part with the grooves. After 21 years, the shaft was very fond of the grooved part, so it took some doing but it came off. Was able to screw the new part onto the threaded shaft underneath. Success!

I have replaced the circuit board, the condenser fan motor but the unit still will not feeze correctly. The bottom of the unit freezes but just barely cools the rest of the freezer and ice box. Have you got any other advice that might help. This is a side by side unit. What else could be the problem. It seems that the fan is not working correctly or it is stuck in defrost mode. The coils where the fan is seem to be icing up but it will not let the fan work. THanks for your help, David Wilson

First I removed the back cover then removed 3 nuts holding the motor. Next I removed the two wires. Next I attached new connectors to the wires and installed the new motor and everything worked perfect!

Service and shipping were fantastic! I would definitely use Partselect again!

Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is now running as it should.

Installed new control knob as directed in the installation instructions found online at your website. Repair went exactly as described.

First I unplugged the refrigerator. Next item was the ice-maker; remove (3) screws and unplug it from the back wall. Third task is remove the (4) screws that attach the back wall of the freezer compartment. Lift the wall up enough to dislodge the center cooling shaft that the fan rides in and remove the rear wall. The last item is the fan motor which is attached to the freezer wall by (2) screws and (3) wires which are easily removed. Change out the motor and reassemble freezer compartment .

Went on line and did a search for Kenmore Washer Select Knobs through the Part Select website. The associated photo made it easy to match to my broken part. Ordered it and received it in 3 DAYS!!! Unwrapped the new part and screwed it on (the knob is threaded)- took longer to unwrap the part than to install it!!! I Love PartSelect.com!!! This was the 2nd time I have used them and will continue to rely on them whenever possible for my appliance repair needs!!!

Screwed the knob on tight. Done

took replacement knob & threaded it back onto post. Done in literally seconds ! ! ! Took longer to open the package than to install new knob.!

It arrived on schedule. Cleaning lady was there. So opened box and in less than 10 minutes it was installed and working.

Unscrewed the old one, no tools required!, and replaced the new one. Unbelievable-easiest repair job I have ever attempted! Product was easy to locate, easy to order-what can I say, this was an easy job, thank you.