This drive hub kit (part number W10528947VP) is for washers.
Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to...
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work glove...
This is lid lock designed for use within various washing machines. This lid lock, also known as a latch assembly, is used to secure the lid of your washing machine during the washing cycle. If your wa...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This 6-pin shift actuator is an authentic OEM part supplied directly by the manufacturer for use in washing machines. The shift actuator is responsible for controlling the movement of the washer trans...
This gray and white washer lid bumper contains a rubber bottom and is sold individually.
$7.95
In Stock
Questions And Answers for MVWC416FW1
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
March 12, 2020
I replaced the lid switch it still won't spin for more than 5sec.When i test with ohm meter 2&3supposed to be 85-155 ohms i get open circuit.With lid closed i test 1&2 i get 0ohms like it is supposed to read.I don't see any way to adjust it,is the switch i just purchased bad?
For model number MVWC416FW1
Hello, Thank you for your question. You will need to remove the lid switch out of the unit, Once it is out you will want to test the motor terminals. You should get a reading of between 1500-1750 ohms. If this is not reading properly and you are sure it is not caused from another issue your switch may be defective. We hope this helps.
Was this helpful?
Thank you for voting!
Steve
November 11, 2023
While spinning it is loud.
For model number MVWC416FW1
Hello Steve, thank you for asking. We would recommend checking the suspension rod, part number PS11703287, to fix the issue. We hope this solves your problem!
While spinning washer is very loud! Bearing? Is there a kit with bearing, seals ? Shaft ?
For model number MVWC416FW1
Hi Steve,
Thank you for your question. The tub bearing is sold with the washer gearcase. The part number for the washer gearcase is PS16220910. There is also a drive hub kit you can purchase. The part number for it is PS6012095. We hope this helps!
cycle setting stopped working except when I set it for Rinse & Spin only. If I set on any other cycle the machine won't follow threw the different stages. I also noticed the lid only locks when it's set on Rinse & Spin cycle.
For model number MVWC416FW1
Hi Cindy, thank you for your inquiry. Based on the description that you have provided, we would recommend replacing the control board, part number PS12347923. Good luck with your repair!
The washer keeps going through the rinse cycle many times
For model number MVWC416FW1
Hello Earl, Thank you for the question. If the drain is clogged, the washing water won't be able to escape the rinse cycle and the washing machine will stall trying to start the rinse cycle until the drain cycle starts. We suggest checking the drain hoses and pump for any clogs or kinks. We hope this helps!
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned
... Read more it back up and got caught up on laundry. good day when the washer is fixed.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
