MSS25C4MGZ08 Maytag Refrigerator - Instructions

It is as easy as is shown in the self-help video. (1) Disconnect the power, (2) Roll the appliance out so you can get to the back, (3) Using a nut driver remove all the screws from the lower back panel then remove the panel, (4) Remove the tensioner wire, (5) unplug the electrical connection to the capacitor, (6) gently but firmly remove the capacitor and starter relay as one unit, (7) preassemble your new capacitor and starter relay as one unit, (8) now simply reverse your steps for installing and you are done! These two parts saved me the cost of a new refrigerator. Almost as easy as changing a light bulb. PS: while you have the panel removed you can do a thorough cleaning with a soft brush and vacuum.

STRANGE ! to moment I installed the filter ALL the internal lights in my refrigerator went OFF and never came back.

Strange !! refrigerator works fine but no more light in it !!

My email is : Lucfontaine91@yahoo.com

DON'T USE earthlink email anymore

Removed old starter and capacitor as per your website instruction.
Plugged in new parts.
Compresser turned on

Hold both water filter reset touch sensors down together. This will reset the water sensor indicator.

1 Remove ice tray
2 turn off ice maker
3 Remove 4 screws
holding on the
cover over the ice
maker
4 remove the two hex
screws holding in
the ice maker.
Remove ice maker.
5 Reverse this procedure for installation.

Removed freezer cover from ice maker, unplugged the harness. Installed the new ice maker assembly,plugged in two wire harness and secured the part and cover.
Results was smooth process, no noice from ice dispenser. Pleased with results. Saved on repairs. Thanks Tom

Found the filter door in toe kick under freezer door. Opening the door ejected the old filter. Direction indicator arrows were found on inside of filter door, rotation of filter to match arrows important. Pushed new filter in to stop, closing door completed insertion of new filter.

Unplug refrigerator.
Pry switch out with putty knife
Remove two wires from switch
Attach wires to new switch
Push new switch into slot

Easy repair, third time in four months, same part. I don't recommend Whirlpool refer's. Stick to the washer and dryers.

Ordered gasket through this site pulled old gasket off, because my conquest had no screws on lining, Put new gasket on top and bottom first and kind of forced the edges into groove using heat gun cause gave me a little problem. But overall, it worked to perfection! Now to buy other gasket for refrigerator door!

Steps to replace Whirlpool evaporator fan motor
1. Watch numerous DIY Youtube videos
2. Move frozen food to refrigerator section, close refrigerator door
3. Cut power to refrigerator
4. Remove all shelves and bins in freezer section
5. Back panel has two parts, a top and a bottom section
6. Unclip small shroud covering screw bolt in upper left corner holding top panel. Remove screw bolt
7. Gently pull and work top panel out
8. Remove screw bolts from all four corners in lower panel and remove bottom panel
9. Verify power has been turned off
10. Unclip grounding wire
11. Unclip evaporator fan motor from power
12. Remove whole cradle holding evaporator fan motor. Note orientation of cradle. Fan blade is slightly angled toward the back of freezer. In other models, the cradle may not be removeable.
13. Remove plastic fan with firm pull
14. Unclip bottom brace to remove evaporator fan motor
15. Replace old grommets in bottom brace and on top of evaporator fan motor with the new grommets
16. Install new evaporator in cradle and clip-in the bottom brace
17. Install new fan blade on motor
18. Place cradle with new evaporator fan motor back in freezer
19. Reclip power and ground wire
20. Turn on power and test if working correctly
21. Turn off power
22. Complete steps from 8 to 2 in reverse

Simply cut the water tube on both sides of connector and push in the new one.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Googled "intermittent clicking noise" or something similar and consensus was it was either the capacitor or compressor start relay. You-tubed videos on how to replace these. Looked easy. Just unplug them from the condenser and replace. Contacted Part Select and staff said 50% of the the time it was the capacitor, 50% of the time it was the relay. I was in a time crunch so I ordered both and they came in a couple of days. I replaced the capacitor but the clicking noise continued. I replaced the relay and problem solved! Maybe I could have gotten away with just replacing the relay, but I had them both by then and figured with a 10 year old fridge, better replace them both at the same time and be done with the problem. So far, so good.

This is an easy fix. The hardest part was just determining which part to replace. But the Q&A's for the ice maker from this site steered me right. And their video on how to install was easy to follow. The only difference I found was my Whirlpool had only 2 electrical connectors instead of the 3 in the video. I finished the job in about 15 minutes so everything in my freezer stayed solidly frozen.