If your refrigerator or freezer is too warm, or making noises, you may need to replace the fan blade. The fan blade attaches to the evaporator motor, which is in the freezer section, to help circulate the cold air into the refrigerator and freezer sections. The fan blade is white in color and made from plastic. This is a genuine OEM part. Please be sure to disconnect the power to your refrigerator before starting your repair.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Fayez
March 6, 2018
My fridge 6wsc20c6yb00 stops cooling and i checked the freezer wall was all iced up. I defrost it and works fine for a few weeks and the the same thing again fridge warm and freezer iced !! its only 4yrs old and don’t know what’s the issue to keep icing... can u plz help
Hello Fayez, thank you for your question. If the freezer continues to freeze up after you've defrosted it there are a parts you will want to test/replace. The Defrost Thermostat PartSelect Number: PS11740424, the Bi-Metal defrost thermostat part number W10260440 as well as the defrost heater part number W10251473. If these parts are tested and are not faulty, the issue could be with the electronic control board part number WPW10372212. I hope this information helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Carmen
August 1, 2018
Loud noise coming from the top center of the refrigerator interior. There is plastic housing there. Is this covering the fan blade? If so, how do i remove the housing to replace the blade? Thank you
For model number AFD2535DEB
Hello Carmen, Thank you for the question. The housing is held in by a few clips. You can depress the clips with a flat head screw driver to release them and pop the housing off. Hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Cluny
March 12, 2020
Loud noise on the motor at top of fridge. Sounds like a filter or blade issue if that is where the fan fits
For model number Kitchen aid KFCS22EVMS8
Hello, Thank you for your question. There are 2 fans in your model. One is the back of the unit to blow cool air over the refrigerator and freezer, and the other is in the back near the compressor that blows the coils. We hope this helps.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Ron
February 11, 2018
Is this just the fan blade, do i need other parts to do the job. My freezer is not cold enough middle to bottom of freezer is frozen solid. Top two shelfs not freezing temp is at 26 f.
For model number MQF1656TEW02
Hi Ron,
Thank you for your question. There are some parts that you will need to check to see which one is causing the issue. You will need to check the fan blade, the evaporator fan motor, the defrost heater, the defrost timer and the bi-metal defrost thermostat. I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Michael
December 29, 2019
My refrigerator coil freezes up / freezer side is fine.
For model number KRSC503ESS01
Hi Michael,
Thank you for your question. Frost on the evaporator coils will prevent air from flowing over the coils. No air flow will cause the refrigerant in the coils to remain in a liquid state and keep it from vaporizing. The refrigerant will travel past the coils and will eventually end up in the compressor and cause damage to it. If there is frost on the evaporator coils, this may caused by the following:
1. A bad defrost heater or the other components of the defrost system.
(The defrost system consists of the defrost heater, the defrost timer and the thermostat/defrost control.)
2. High Humidity
3. An evaporator fan motor not working correctly or not at all.
4. No load on the evaporator coil.
5. Dirty evaporator coils.
6. Defrost intervals that are set too far apart. We hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Alvaro
February 3, 2018
I need a replacement fan blade
For model number ED5THAXMS10
Hello Alvaro, Thank you for your inquiry. Part# WP2190685 is the condenser fan blade at the back of the fridge, and part# WP2169142 is the evaporator fan blade in the freezer section. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Arlene
April 24, 2018
My refrigerator is making a loud screeching noise. It appears to be coming from the freezer. In addition, the refrigerator is only one year old. Please advise as your site is recommending it may be the evaporator fan motor.
For model number 106.51139214
Hello Arlene, thank you for your question. The screeching noise is most likely the evaporator fan motor that is located behind the back wall of the freezer section. I would suggest replacing the motor, which is
Evaporator Fan Motor Part Number: PS11740362. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Harmandar Singh
May 28, 2019
Freezer working fine but evaporator fan motor not flowing any air to refrigerator top went.? switched off machine for a day it worked fine then back with same problem. any suggestions.?
thanks.
For model number KBFS22EWMS9
Hello Harmandar, thank you for writing. You will want to replace either the Evaporator Fan Motor part PS11773024 or the Fan Blade part PS11738973.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Rob
19 days ago
The refrigerator is about 13 years old and the fan seems to be running constantly and making noise. When I open the freezer door the noise stops but once the door closes the noise comes back. Would this be the evaporator fan issues. Thank you in advance for the help.
For model number Afd2535fes
Hello Rob, thank you for contacting us. We recommend you check the following parts: the evaporator fan blade, part number PS11738973, and the evaporator fan motor, part number PS11748697. Please make sure that the motor fan blades are not hitting any other part/thing and are not damaged. If the blade is found to be damaged, replace the fan blade. If the issue persists, then you need to check and replace the evaporator fan motor. Thank you for the inquiry, good luck with the repair!
FREEZER WORKING GREAT BUT REFRIDGERATOR IS WARM. DAMPER IN FRIDGE OPENS AND CLOSES AND AIR CHASEWAY BETWEEN FREEZER AND FRIDGE IS FREE FROM ICE BLOCKAGE ( HAD THIS HAPPEN BEFORE). EVAP MOTOR IS RUNNING AND FAN BLADES ARE SPINNING. ANY SUGGESTIONS WOULD BE GREATLY APPRECIATED
For model number AFB2534DEW
Hello Steven, thank you for contacting us. We would recommend checking the evaporator coils for ice build-up. If you notice the built-up ice, defrost it manually and check the defrost heater, part number PS11743496, and defrost thermostat, part number PS11743535, for continuity. Also inspect the damper control assembly, part number PS11750106. It controls the cold airflow from the freezer compartment into the refrigerator compartment. If this does not help, the issue is probably related to the electronic control board, part number PS11755733. It manages the functions of the refrigerator such as cooling and defrosting time. We look forward to hearing from you if you need assistance with placing an order through our 7-days-a-week customer service. We hope this helps!
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Noisy Evaporator Motor/Fan
Our 48" Built-In KitchenAid Frig (1999 model)started getting very noisy about 3 years ago. Two different repairmen plus KitchenAid said 'that was the way it was'. I figured out the noise was coming from the evaporator motor/fan but the repairmen said it was just because moisture was freezing on it and replacing the evaporator motor/fan probably would not make a difference plus it would be very expensive. When I discovered PartSelect and that I could order the parts (about $80) myself I thought why not. It was simple to replace. Removed cover inside freezer compartment - detached bracket and electrical wires - replaced with new motor and fan. Now you can hardly hear the frig running and it runs half the time - more efficient. I can't believe we lived with that noise for so long. Thanks to PartSelect I proved KitchenAid and the repaiirmen wrong and did it myself! Thank you PartSelect!
about half my time was spent figuring out how drawer front and back panel were held in: remove wire baskets lift freezer drawer front to remove remove ice maker...held in by 3 screws,then unplug remove back panel screws then on this model, there is a vent towards the top of the panel that is held in by unseen plastic clips on the top left and top right that had to be pressed in with a screwdriver to remove unplug freezer evap motor also held together by clips remove and replace motor (old fan blade pulls off and slides on new motor shaft) plug motor back in reinstall back panel reinstall ice maker reinstall drawer front and baskets
Removed six screws from cover in the back of the freezer. Removed old fan . Removed power wires from old motor. Unclipped old motor from the mounting bracket. Replaced old motor and reversed the rest of the parts. Done
simply removed wires from the old motor and gently lifted it out by by the metal clips - put the old bracket on the new motor, snapped on the new fan, replaced the wires, reinstalled the shield. All done in about 15 min.
remove shelves in freezer compartment incl.holders(slide up to remove) Remove lamp/shield Remove panel (six phillips screws) disconnect motor pull off fan blade squeeze bracket holding motor to remove remove motor. Re-assemble (in reverse)
Power down the refrigerator with the disconnect switch under the upper panel. Empty the freezer. Remove the bins and shelves. Use nutdriver to remove the screws holding the back trim panel in place. Remove the panel. Take picture of the wire connections going to the motor. Remove the motor mounting bracket. Remove old motor/fan assembly from bracket. Press new fan blade onto new motor. Transfer each wire from old assembly to matching location on new motor. Mount new motor to bracket. Remount bracket to freezer. Reinstall back panel. Turn power back on. Enjoy quiet refrigerator.
Original freezer fan motor ( 1996) was starting to make a growling sound and at one point had stop working. I took the panel out of the freezer and took the motor out ( two screws) and moved the motor shaft, this helped to free the sticky motor and get the the refrigerator back up an running as i di
Take pictures of original setup in case you need to refer back and turn off power at the panel. Remove the White panel in the back of the freezer ( 16 screws). Unscrew two screws holding the motor / fan blade and remove. Remove the hot/neutral and ground wires and remove the motor/fan unit. You will have to use the old brackets as the new motor does not come with them so don't throw the old motor just yet. The brackets will have to be removed from the old motor by removing two 1/4 screws and placing the brackets onto the new motor in the same fashion. Once this is complete, just reassemble new motor in reverse order. since the fan has to fit into a tight opening and the mounting brackets have to line up to screw the whole unit in, I assembled everything lightly tightened and mounted the unit to make sure the screws lined up and the fan blade had clearance in the fan opening so that it did not rub. Since the bracket screws are not 100% tightened, this allows some wiggle room to adjust. Once everything is lined up, tighten all bracket screws 100%. Insert the wires and your ready to go. Reinstall the White panel and 16 screws. Motor has been working great since installation.
Upper 1/2 of freezer not cold. Upper half of refrigerator not cold
Removed all drawers in freezer. Removed screws from slides for drawers on left side of freezer. Removed evaporator coil cover screws from behind where freezer drawers and shelf’s are. Removed wires from motor. Removed blade. Pressed black clip on both sides and removed motor. Reverse this process and put unit back together. Now fridge works great.
On the door cams. Just remove the top hinge on door. Replace upper and lower parts and replace door.
Steps to replace Whirlpool evaporator fan motor 1. Watch numerous DIY Youtube videos 2. Move frozen food to refrigerator section, close refrigerator door 3. Cut power to refrigerator 4. Remove all shelves and bins in freezer section 5. Back panel has two parts, a top and a bottom section 6. Unclip small shroud covering screw bolt in upper left corner holding top panel. Remove screw bolt 7. Gently pull and work top panel out 8. Remove screw bolts from all four corners in lower panel and remove bottom panel 9. Verify power has been turned off 10. Unclip grounding wire 11. Unclip evaporator fan motor from power 12. Remove whole cradle holding evaporator fan motor. Note orientation of cradle. Fan blade is slightly angled toward the back of freezer. In other models, the cradle may not be removeable. 13. Remove plastic fan with firm pull 14. Unclip bottom brace to remove evaporator fan motor 15. Replace old grommets in bottom brace and on top of evaporator fan motor with the new grommets 16. Install new evaporator in cradle and clip-in the bottom brace 17. Install new fan blade on motor 18. Place cradle with new evaporator fan motor back in freezer 19. Reclip power and ground wire 20. Turn on power and test if working correctly 21. Turn off power 22. Complete steps from 8 to 2 in reverse
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Brad T - January 28, 2022
Verified Purchase
Easy repair
Great
★★★★★
★★★★★
Jami E - August 3, 2018
Verified Purchase
Works great easy to install
Easy to install took care of the problem
★★★★★
★★★★★
Corey B - July 10, 2018
Verified Purchase
Not the part we expected
We were told this part would be the equivalent to the part we needed. It was not. We also paid for overnight shipping and got the part a week later. Now we had to ship it back and paid for the shipping to ship back the incorrect part. Will not be ordering from this company again.
July 27, 2018
Hello, Thank you for leaving a review on the . Sorry it had taken us so long to get back to you. We have been a bit more popular then normal and are now able to check our reviews. Checking the order I am showing you have already contacted us to address the issue and the shipping fee was refunded. Please let us know if there is anything else we can assist you with.
★★★★★
★★★★★
Douglas S - June 5, 2018
Verified Purchase
refridge fan motor
this part was ridiculous. it had to be shipped from china and cost whopping .$.25 or that is all it is worth.i did not even attempt to use it cause my 2000. fridge could not possibly need or be fixed with this cheesy part. i paid $33. for this stupid part. this company should be ashamed of their selves for selling this for that price. a 3 inch round piece of plastic weighing in at a whopping 3oz. could not possibly be worth the mailing price. what a joke. this company ripped me off.
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
