MLE23PDAUW Maytag Dryer - Instructions

We could not find directions for the brand that we have. First we took the back off, which we did not need to do.
lift the top of the dryer, remove the front remove drum. Place belt on front of motor, wrap double belt around support on bottom of dryer, open the remaining belt and stretch around drum. Hold drum in place, replace front and top.
Need at least 2 people, not at all intuitive.

I removed the dryer door and attaching hardware to other covers. Raise the top cover and prop it up. Remove the drum retaining cover and disconnect the door switch wires, making note of their locations. Release tension on idler and take belt off of motor. Pull the drum out with belt still around it. Vacuum lint and dust from inside cabinet. Use snapring pliers and remove the snaprings on the drum rollers. Remove the old rollers and washers, clean the shafts and apply a light film of oil on the shafts. Install new rollers and plastic washers on shafts and secure with snaprings. Remove the "E" clip from the idler shaft and remove the old roller. Clean and lube the shaft and install the new idler and clip. Place the new belt on the drum with the ribs against the drum. Put the drum in place and install the front drum retainer. Position the belt around the motor pully and tensioner. Rotate the drum to get the belt to track. Attach the remaining covers.

First removed front door 2 screws holding it to frame, then removed 2 screws holding front cover panel on tilt out front panel, used vac to clean inside, removed idler arm with pully attached, replaced with new parts when I did a test run still had a llitle squeek, the drum support wheel on right looking from front making some squeeking,I went back in removed part shaft had small rust spot cleaned with jewelers cloth lubed and wiped off, no more squeek I wish I had ordered new drum wheel when I ordered idler parts, then I could have done a complete overhaul now I know more I have never worked on a dryer before the drawings on the web site heleped a lot

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

Others have described how to remove 4 screws and remove the front panel of the dryer. The problem I saw is that some screws broke off and fell inside while others remained on the separated baffle. The old screws that I found were 1 1/4 inch. The parts manual indicates a replacement screw that is 1 inch long and a number 10 width. One set of holes for the baffles has slotted holes. It appears that wear in the paint indicates movement before breaking off. My solution to the slotted holes was to use washers on the screws and to tighten the screws in the position where any force was not going to move the screws to the center position of the slots. The force of the separation caused the slotted holes to expand.

The video was excellent and made for an easy repair. Would highly recommend.

Unscrewed door and front panel. Pulled and took the, off. Used standing flashlight to illuminate the area underneath the dryer barrel. Tried various tools to take out broken plastic remnants. Then, used small electric nutdriver to screw the tall baffle into place with newly purchased metal screws. Was a bit hard to reach and tight but finally worked once I found an appropriate tool and top.

I took out the old worn out part and replaced with the one I order.

Remove the door and the plastic brackets on the other side of the door opening. Remove the front cover by gentally pulling from the top first. Support the dryer basket (I used an old towel and a block of wood. With a 1/2 inch wrench remove the Roller Shaft with the Drum Support still attached. Replace new shaft and drum support. (always replace both at the same time or you will find that the problem will come back much sooner.) Careful when installing. Make sure that the new non metalic washers (suppied) are propery seated when you are tightening down the nut.

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

After taking apart the machine (applianceaid.com has slideshows for most major appliances - very comforting and reassuring - highly recommended), I used a shop-vac to clean up all lint and dirt. After getting the retainer ring off the drum roller shaft (snap ring pliers highly recommended), I replaced the drum roller along with the glides which were completely worn through (rivet gun required). I reassembled the dryer to find that the drum wouldn't turn, so I placed another order for the other drum roller and replaced the belt too. Back in business.

Unplugged the dryer (don't forget this step guys!!!)

Pulled the front off the dryer (4 screws) and swapped the motor out - take off the belt, pull the blower wheel (by removing the snaprigs and squeeze collar), then pull off the motor retaining clips... unplug the motor and install the new one in reverse. Took me less than 2 hours and my dryer works like new.

WAY CHEAPER than a new dryer!!!

Read the instructions included with the parts, removed the 2 screws on the front of the dryer. Removed a couple of wire connections and 4 screws that held the drum in place. Moved the drum enough to have access to the roller supports. I removed the nut from the back of the supports with a 1/2" wrench. Placed the new supports on the old support pins and reinstalled them. Put it all back together. Probably the most difficult task was getting the drive belt back on the drum correctly. I was done in just over 1 hour.

I ordered the wrong motor for my dryer PN PS3500892, the right one was PN PS11741125, the motor specs were the same but the shaft were different lengths and different blower fan and fasteners. Since I had the wrong motor in hand I worked with Parts Select to order the correct blower fan and fasteners for this motor. Got it all installed and everything fit as it should. even though this was a different part than I had before it saved me $100 by doing it this way, Thanks to Parts Select for helping me through this maze with me asking many questions about part sizes and fasteners. They did this all for my savings. Most parts places would not have gone this far for the customers benefit. Thank you very much Parts Select !