MLE2000AZW Maytag Washer Dryer Combo - Instructions

Unplug washer, turn off water, disconnect supply hoses.
Drain washer by removing the one screw holding the hose on the bottom rear of the washer, drop the hose to the floor and let it drain (you may want to take washer outside)
Remove four screws holding rear panel
Locate the pump and disconnect the two wires. Wires can be attached to either terminal when reinstalling, orientation is not important.
Using 5/16 driver, loosen the hose clamps on the inlet and outlet pump hoses then remove hoses from pump.
Twist the pump counter clockwise then pull straight up to remove.

Followed the inclose instructions that came with the Motor and Control Board Conversion Kit very easy.

Apparently the only way to solve the notorious mold problem on the rubber gasket of the Maytag Neptune front-loading washer is by replacing the door gasket. I ordered the boot kit from you and my husband attempted to do the job without the benefit of an instruction sheet, but I was finally forced to download the repair manual from the Maytag website. Using a screwdriver to remove the the front door, the detergent dispenser, and the shroud, he was able to remove the old gasket, though stretching the spring that held the gasket in place required some strength. The only tricky part was stretching the spring again that holds the replacement gasket in place. With a little ingenuity, a screwdriver (and some dishwashing liquid to make the task a little easier) he finally accomplished it. It took him over 3 hours, but the job is done and the washer seems to be working fine. Your service was fast and efficient and I wouldn't hesitate using your service again, but enclosing a detailed instruction sheet would have been helpful. Now that he knows how to do the job he acknowledges that the it shouldn't take him more than an hour the next time, should the gasket need replacement again. Meanwhile I am going to try tackling the mold problem by leaving the front door open after wiping out the water that remains on the door gasket after each wash.

Just put the new one in. I also would like to tell you that I was VERY PLEASED with the service I received from your company. The part arrived very fast. Thank you very much. I will use your service again and will recommend you to others.

I used my screw driver to pry the old female end of the latch from the dryer unit. I forced the new female part of the latch into the hole and bang...45 seconds later the door closed securely --like new!

no repair needed but the part could not be found in the area i live . ordering was easy and deliver time quoted was very resonable but the part came the very next time that was wonderful.

Very easy with a tip from the video that was provided from Parts Select.
Thank You
Joseph Errico

My repair (replacement of Maytag Neptune front load washing machine tub bearings) went well — knock on wood. The reason I took on the job somewhat confidently is I read online (probably from your site) the testimonial of someone who successfully did the same repair I faced. It is this persons sharing the recount of what it takes to do this job that gave me the motivation to take it on. For me it was around an eight hour job being my Neptune is a stackable (with the drier ontop). It has been a week now of operation with about 10 loads through the washing machine. It is sooo nice not listening to the previous worn bearing sound best described as a jet plane winding-up during taking off coming from the washer during its spin cycle. I pray the shaft seals stay snug. The job definitely was a major undertaking. Replacing the seal and bearing myself I saved probably saved $900.
Scott

Removed the Rear and Front Skins of the Washer. Removed the Belt and Tub Drive Wheel from the rear of the Tub. Removed the Front Rubber Gasket and Bracket Assy. Removed the Tub Cover w/Seal, Spinner Balance Ring (both were damaged.) Knocked the Spin Tub forward with a sharp hammer-rap on the Axle (the Axle is pressed into a Bearing that remains in the Stationery Tub.) Removed the Spinner Assy--found one of the securing bolts on the tri-Arm Support sheared off causing an imbalance. Also, the tri-Arm Support was cracked in various places. Replaced all bad parts using the Spinner Support Assy Kit and new Plastic Washers. Replaced everything else in reverse order then tested. Finally, reinstalled all Machine Skins. Very successful, about 3 hours.

Opened the back panel of the washing machine. Removed the old belt and wrote down the part number. Shopped online for a suitable replacement and found a perfect match at part select.com. I put in an order and it was delivered in a couple of days! I opened the back panel of the washing machinie again. This time I decided to also replace the isolators that came with the kit. For this, I had to unscrew the motor and gently tug it free. I placed it on the floor of the washing machine. I then replaced the 2 isolators as described in the kit, reinstalled the motor and put the screw back on. I then proceeded to place the belt on the motor and on to the wheel. This took couple of tries to get the grooves right. I then tested the washing machine on a rinse cycle and things looked good. Its been working fine so far.

use an online repair manual for your model, but in the manual it states that the tub bearings are not replaceable, if you are a skilled person capable and competent with fixing mechanical things you should be able to replace the bearings, don't forget to put in a new seal. the bearings can be found at grainger.com , have the old ones in hand for proper size as these bearings are only sold by dimension. This repair will take some time and patience.

I put the new one in . Nothing to it.

If your dryer is squeaking it is most likely either the idler pulley or drum rollers. First I took apart the dryer to see which parts I would need. I checked the drum rollers by spinning them with my hand to see if they spun freely and also checked them to see if they were loose, they were okay. Then I checked the idler pulley and found my problem, it was hard to spin it so I figured the bearing was shot. I sprayed some lubricant on the bearing to help with the squeaking while I waited for my parts. It took about 30 minutes to diagnose my problem and put the dryer back together.
I took some advise from another story saying to get the whole idler arm, shaft and pulley assembly. It might have cost me a few bucks more, but I did not want to run into the same problem he did (the pulley bearing was fused to the shaft). It took me about 20 minutes to take apart the dryer, install the part, and put it back together. If you are pretty good with fixing things, you should have no problem doing this repair.

After taking the dryer apart, I found that one of the drum support rollers was barely hanging on the pin and was the main cause of the metal on metal squealing noise that became increasingly worse over a month's time.

I replaced both rollers, the idler pulley, and put on a new belt after giving the dryer a thorough cleaning.

It was a 100% success and fixed the problem making the dryer work and sound like brand new again.

Pre-ordered the spinner support & seal kit, searched online and found a repair manual, disassembled machine according to the manual, removed snap ring outside of rear bearing, used hammer and drift punch to remove bearings, went to local bearing supply store and purchased 1-6206 2RSJEM and 1-6207 2RSJEM for a total of $43. Used needle scaler to remove the ~1/8th inch of scale from inside of the outer drum and outside of the inner drum and other parts encrusted with scale. Installed new bearings and the seals and new spinner and reassembled the rest of the washer. Now we can't hear it when it spins!