MGR8772WS0 Maytag Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Plug in the element put the wires back in the hole and screws the element on and that was it. Worked great.

I turned off the gas at the back of the oven & unpluged it. I then removed the 2 screws that secure the oven bottom plate to the oven. Once removed, that exposes the oven burner & igniter. There are 2 sscrews that secure the igniter to the burner; remove those screws, & pull the igniter wires out, to expose the connector. Unplug the connector, & the igniter is free. Just reverse the process with the new igniter.

removed door (no tools required - just lift and pull door out of range). removed front door panel with a screwdriver. removed/replaced door hinge with nutdriver. replaced front door panel with screwdriver. replaced door on range (again, no tools required). then installed tip-over bracket to floor/wall behind range. measured location, drilled pilot holes and installed wood screws into the floor and rear wall stud.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

seamed easy enough. Found the part and it looked identical, However I could not see the connector in the picture because the logo covered that part of the picture. Had to cut the connector off the old igniter and crimp it on to the new ingniter.

We took the interior floor out, pulled the stove away from counter, before that turned all electricity to the house off. Then we unscrewed the ignitor inside then underneath unplugged it and plugged in the new one, cleaned to oven and screwed the ignitor in and replaced the interior floor and we were done.

Replaced gas oven ignitor

The repairs was easy,once I found the problem I turned the gas off and unplug the power supply cord. For the oven gas valve I used a 5/8 wrench to take the gas supply line away from the side of the valve inside the over. I used a 1/4 nutdriver to remove the two screw holding the braket down over the valve. For the glow-bar I donnected the power supply plug and used a 1/4 nutdriver to remove two screw holding it in place next to the brun.

followed instructions from repair manual.

I unplugged the power to the stove first,
I removed the racks and cover plate at the bottom on the oven. Located the 2 screws holding the element igniter in place. I pulled the stove forward and removed the back cover plate and unplugged the old element.
Installed the new element and tested the igniter, special note my oven would not ignite the propane with the cover plate not first being installed. The igniter glowed but would not ignite fuel.

1. Turn off the gas (propane)
2. Unplug the oven.
3. disconnect the gas line and pull the oven out.
4. remove the back panel to access the igniter.
5 disconnect the igniter.
6. unscrew igniter/gas assembly and remove from oven (two screws).
7. unscrew igniter (two screws)
8. replace igniter with new.
9. reassemble in reverse order.
10. turn on stove.
11. Happy wife, happy life.

I simply pulled the stove away from the wall, disconnected the gas and electricity. Then took the pan out from stove. At which time I used a socket to remove the two srews and then unplugged the part from the back of the stove. After that, reattached the screws, plugged it in, reconnected the gas and electricity, and pushed the stove back against the wall. Fired up the oven and it has worked like a champ ever since!

Removed oven bottom were you see the light glowing from then unscrewed igniter unpluged then took it out and put in new one went well i would do it again works great

We ordered the replacement igniter and basically was very easy to replace. We ended up spending $50 for the part as opposed to spending $261.00 that Sears was going to charge.