MEW6630CAS Maytag Wall Oven - Instructions

Shut of power to unit, removed front display panel, located lower circuit board. Removed the one screw holding existing board and installed new board, then swaped wires from damaged to new. re-installed front panel, turned pwoer back on, that was it. The unit is working well.

Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

Removed upper cabinet doors. TURN OFF CIRCUIT BREAKER. Removed 4 screws holding control panel cover. Slid cover up and off. Disconnected 3 sets of wires. Removed old clock assembly, and replaced with new. Hooked up 3 sets of wires. Slid cover back on, attached screws.
Flipped circuit breaker - it worked!

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

The digital clock was a snape to install but the long oven sensor required installation from the back. This means removing the double oven from the cabinet. I'm saving this repair for the installation of new cabinets.

The door came off easily after I removed the two hinge covers that are attached to the oven. Taking the door off can be done with one person but ideally two.

The new parts fit in perfectly and the hinge pin used for shipping comes out easiest with a pair or wire cutters (you do not cut it just grab it and pull).

After that, re-assemble the door and drop in place. It was a snap.

FYI...the shipping was ultra fast and the price was great.

No issues whatsover with the entire process.

Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.

I slide the oven out from the counter and unpluged it. I removed all the oven racks. I then removed the machine screws that held the sheet metal that covered the back of the unit. This made it a lot easier to disconnect the long oven sensor wire and put the wire through the insulation. I removed the two screws on the inside of the oven that held the sensor onto the inside rear wall of the oven. The old sensor did not test too bad but the temperature is reaching the set temperature. I still had to adjust the oven temp up ten degrees using the control panel. I have learned that it takes a few cycles of the element going off and on during the warming to reach the desired set temperature. One more issue is that the buzzer goes off signaling that the set temperature has been reached when it has not. When I set it for 350 F the buzzerr goes off at 280 F and I have a good oven thermometer. I own three oven thermometers and they all read the same. We use to have nothing but Maytag appliances but no more. We have had issues with Maytag front loading washers and ranges. PartSelect is great. Good prices and fast delivery.

Removed screws holding in control panel. Replaced clock assembly following instructions listed by others. Easy. Wife happy.

Thanks for the hint from this forum.
My display became very dimm, eventually unreadable.
WIth suggestion from this forum, I replaced the Electronic Clock assembly. I took me about 15 minutes. The display works perfectly fine and makes the oven look like new with its nice bright digits.
BJ

Removed three screws from top of display/control panel. Open upper oven door and remove 4 screws from botton of display/control panel. Pulled panel off and rested it face down on top rack of I pulled out of upper oven. removed 2 wiring harnesses and ribbon wiring form clock assembly. Remove four screws with nutdriver and remove clock assembly. Replace clock assembly and reasseble in reverse order from above.

Easy repair- read the other reviews and followed it. Pretty straight forward.
Quick delivery on the part.

Unscrew 7 screws on foace plate,unplug computer board,replace with new board,rescrew 7 screws ,finished

Removed the screws pulled the control panel out and plugged in the new one......it was easy. It was 2 days before Thanksgiving, we were so happy to get it fixed.