MAT25CSEGL Maytag Washer - Instructions

1. Remove front panel with phillips screw driver.

2. Remove hose from drum and exit pump

3. replace hose with new one (used some silicone grease on hose)

4. Tightened clamps with nut driver

5. ran a couple loads of wash to check for leaks

6. found none

7. replaced front panel - Job done

Followed video that came with part.

The directions that were available when placing the order were right on

Replaced the air tube, existing one had been chewed by mice was easy to replace and solved the issue

removed the front panel on washer.
unscrewed the top and bottom hose clamps on the hose.
removed the damaged hose. put on new hose clamps on the new hose.
made sure the larger diameter end of the hose was on the bottom.
pushed the new hose into place on the tub water outlet and on the top of the pump.
adjusted the hose clamps into place and tightened them both.
replaced the front panel on the washer with two screws on the bottom of the panel in the left and right corners.

Watched the video first that was offered. Stating what tools needed size of socket needed. Step by step and how to do the job. Which was very helpful.

I removed the front of the washer (two screws) and found the drain hose to be cracked near the top where it attached to the drum. A hardware store hose was inadequate because it crimped when bent in an S shape as required, so I ordered the proper part amd installed with two new clamps.
I bought a 5/15 socket driver to do up the clamps, and all is fine.

removed cover, disconnected small water tube and disconnected electrical connections. Reversed above to install new piece. two nutdrivers required. Channel locks for supply hoses.

I order a water inlet valve from this site It was the best buy around. The email from the site part came with a video how to change it. It was a 15 minute job. One 5/16 nut driver to remove the inlet valve and pliers to remove the hoes from the valve. Easy off easy on.

Well I looked on line to see if there were any similialtys to my problem and followed what they had done on their washing machines. I replaced the water pump,the slide control below the motor,and the lid switch.None of these items worked.I called a tech.and he informed me that it sounds like the transmission is bad ,he is coming to my house tonight to take a look at the machine.

Looked online and found a video for the repair consistent with a water leak. Two screws to remove the front panel of the washer, loosen two hose clamps, remove belt (by hand) and three screws to remove old water pump. Replaced pump, replaced belt (made sure it was tight, but not too tight), replaced water hoses, placed cover back on the front and I was done. Maybe 15 minutes tops. Very, very easy. Works like a charm and saved probably $100 in labor.

Terrified that the washer water value would blow due to the noise... Diagnosed the problem, ordered the part and it took only 10 minutes to fix. The hardest part was moving the washer in the confined space, which required moving the driver out and sliding the washer at a 45° angle in order to reach the access panel. Once access gained it was straight forward. Step 1 removed fill hoses from supply. Backed the valve assembly out; detached water hose from value assembly with nut driver; detached wires'; value released; added new value and reverse process. Checked for leaks, reassembled fill hoses with new washers (stainless steel hose), ran cycle, checked for leaks, replaced washer in original position Need commend the video producer and repair person in the video. The narrative gave me the confidence that, Yes, I can do this.

all went well until testing. tub level did not shut the water off, caused a spill

Watched your video and followed your instructions and it was very simple.We bought our maytag washer in 1988 next year it will be 30 years old we raised 3 children and for $21 and your video I hope to it last another 30 years

Followed the directions posted by another user. His tips were very important and helpful. At first we only ordered parts where it was leaking, then decided we might as well change the remaining parts as recommended by the other user in his description. This is the FIRST issue we have had in 19 years of use. Ordered the parts, received them quickly and correctly. Installed them and it works like a new machine. This Maytag will probably last another 19 years.