Maytag/Maytag_Thumb/37308.gif
See part 9 in the diagram
Replacing your Maytag Washer Plastic Injector Nozzle play video
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Plastic Injector Nozzle

★★★★★
★★★★★
7 Reviews
$10.76   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11738878
Manufacturer Part Number WP213015
Manufactured by Whirlpool
Product Description

Plastic Injector Nozzle Specifications

The plastic injector nozzle is used in washers and dryers. It is 3 inches long and is white in color. If your washer is leaking water, replacing the nozzle could solve your problem. For this repair project, you will need a 1/4 nut driver, 3/8 socket with extension, and a stubby Phillips screwdriver. To begin the repair, first remove the front panel by removing screws from the bottom end of both sides. Next, locate the two bolts in the interior of front panel and remove both. Pull bleach dispenser hose off before removing the top cover of washer. Remove clamp that holds the hose to the valve assembly to access the nozzle inside rubber valve and replace with new nozzle. Refer to the instructions provided by the manufacturer for further guidance.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Maytag, Jenn-Air.
Part# WP213015 replaces these:
AP6005818, 213015
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

1 question answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Wayne
    October 23, 2017
    Water coming out of the bleach dispenser tube.......pouring on floor......what is the problem?.......is the injector tube in the tube?
    For model number Maytag A512
    Hi Wayne, Thank you for your question. I would suggest taking a look at your tube to see if there are any holes or tears which could cause the leaking. If there are, you would have to replace the tubing. Good luck with your repair.

    3 people found this helpful.

    Was this helpful?
    Thank you for voting!
      Part Videos

      Replacing your Maytag Washer Plastic Injector Nozzle

      Replacing your Maytag Washer Plastic Injector Nozzle play video
      Customer Repair Stories
       Average Repair Rating: 3.5 / 5.0, 56 reviews. What's this?
      Sort by:
      Sorry, we couldn't find any existing installation instruction that matched.
      Front load washing machine leaking on floor while in fill mode.
      Removed two screws at bottom of front panel and then removed front panel. Then removed two self-tapping bolts (one on each side) holding top panel in place and swung the panel up, out of the way, to expose top of tub and water injection components. Cut off one pinch clamp and loosened screw clamp holding two injector hoses to the injector sleeve. Removed these water injector hoses from injector sleeve assembly which is mounted on top of left side panel upper flange. Replaced deteriorated rubber injector valve, nozzle and the sleeve for the injector (plastic housing containing the injector valve and nozzle). Also replaced deteriorated injector tube seal where injector tube elbow mounts to top of tub assembly. Reinstalled injector hoses with a replacement screw clamp to replace the one cut off. tightened the new clamp and the other, original, screw clamp and checked for leaks. This solved the leakage problem. Secured top panel and re-installed front panel. Hardest part of the task was determining where the leak emanated from but once found and parts ordered, it was a relative snap to fix.
      • Catherine from Wyandotte, MI
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Screw drivers, Socket set
      172 of 180 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      For several years the washer has moaned and groaned while filling, and filled slower than when new. It seemed to be associated with the inlet water valves. Then, it began to leak water from time to time, with the frequency and amount increasing.
      I thought I had only a water valve problem - both the noise and leak seemed to come from the water valve assembly - but I had two. After replaced the water valve (a job which was easy to do as the assembly was easily accessed from the rear of the machine) the moaning stopped but I was surprised to discover that I had a stream of water pouring from under the machine.

      I pulled the front panel (two phillips head screws needed to be removed) and raised opened the top assembly after removing two hex screws. (The diagram on PartSelect.com was helpful in understanding what I had to deal with).

      I observed the fill action, and found that the water was leaking from the slots in the fill nozzle sleeve, in the water injector hose line. (The new inlet water valves had increased the pressure at the fill nozzle and increased the leak from that point which I had not suspected to be the source of the leaking water).

      The basic problem was that the rubber valve sleeve had shrunk in length and was no longer flexible, allowing water to come out of the sleeve slots. I ordered an injector nozzle and valve and installed them in the original sleeve bracket in just a few minutes (two clamps had to be loosened, and the hose sections pulled back to insert the valve and nozzle assembly). (I had also ordered a replacement bracket just in case the old one might break, but it was not the correct part and the old one was fine.)

      I checked for leaks and closed up the machine. Problems solved! It is now both quiet and leak-free.

      (Moral, open the machine and check the nozzle for leaks - even if you suspect only the water valve assembly. The nozzle valve is located above the water valve and its leaks drop onto the water valve, making it look like the water valve assembly is the source of the leak.)
      • David from Macungie, PA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        1- 2 hours
      • Tools:
        Nutdriver, Screw drivers, Socket set
      • Parts Used:
        WP216201, WP213015
      64 of 69 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Washing Machine was leaking water
      Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years old and this was the first problem--hopefully it is now good for another 20 years!
      • jeff from lindenhurst, IL
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Screw drivers
      • Parts Used:
        WP216201, WP213015, WP596669
      55 of 73 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Leaky injector nozzle
      Water was leaking at the injector nozzle during the fill cycle. I could not visually see any damage to the existing part, but, ordered replacement parts, anyway. The new parts arrived and looked EXACTLY like the old ones. Clearly, the new parts would leak, too. So, I cut a three-inch length of 3/4-inch OD pipe and spliced the two hoses together, completely eliminating the troublesome parts. The washer works fine and does not leak. And, it fills much faster, now. I still have no clue as to the purpose of the injector nozzle nor do I know why it did NOT leak for 30 years.
      • Michael from Lindstrom, MN
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        More than 2 hours
      • Tools:
        Nutdriver, Pliers, Screw drivers
      • Parts Used:
        WP216201, WP213015
      33 of 38 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      washer was leaking onto the floor
      First I disconnected the power and turned off the water supply. Then removed the front panel of the washer by removing the two phillips head screws from the lower left and right front of the machine. I then removed the four hex screws at the corners of the top of the machine using a socket set. The two screws in the front of the top come out through the inside and the two screws in the back come out through the access holes in the top. Next I disconnected the bleach/softener tube from the upper end to allow the lid to be raised. Then I swung the right hand side of the lid up fully and rested it on the left hand side support using the braces provided on the lid and resting the weight on the attached support string. The injector valve, inector nozzle and injector bracket are right on top on the left hand side. The bracket is taken out by removing one hex screw on the underside of the bracket. The valve and nozzle are removed by loosening the hex screw on the hose clamp, To replace, first assemble the rubber sleeve and plastic injector. The large end of the plastic injector should fit squarely into the slot of the rubber sleeve. To insert this assembly back into the molded end of the injector hose I used a small amout of laundry detergent to lubricate the large end of the rubber sleeve. This allowed the part to slide in without displacing the rubber sleeve from the plastic injector nozzle. Now, I replaced the associated parts (lid and front panel) and turned the water on and plugged the washer back in. No more leak. Thanks to PartSelect.com my repair was easy. I did not need to replace the injector sleeve bracket but purchased the new one in case I broke the old one during the repair.
      • Richard from Ashley Falls, MA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Screw drivers, Socket set
      • Parts Used:
        WP22213057, WP216201, WP213015
      32 of 36 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Washer leaked from top, left corner of machine.
      Removed front of machine; then tilted back the top of machine, after removing the two screws in top front. Removed the old parts, trimmed the injector hose which was slightly longer than necessary, put new injector nozzle in ruber injector valve and inserted into the new sleeve, clamping the new hose to sleeve as well as clamping the remaining functioning hose to sleeve. The new sleeve mounting bracket was slightly different from the old one, but I was able to make it work with a small block of wood and two screws. The washing macine no longer leaks, the parts arrived timely, and the price was right. Thanks.
      20 of 25 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Water was leaking on the floor
      I took the front panel off the machine and then removed the two screws that held the top on. Cut the hose clamps off the hoses and replace the injector sleeve, valve, housing, and hose to tub. I am not sure what the function of this is, other than to inject air into the water before it goes into the tub. Very easy to do if you know how to open up the washing machine.
      • Mark from Park City, IL
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Pliers, Screw drivers, Socket set
      17 of 19 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      The hot water intake valve did not function
      This clothes washer is 35 years old and runs like a champ. I did notice a bit of water below the left rear and assumed that a hose was leaking. I let it go for about 6 months, until I could fit it into the "to-do" list. During that time, the hot/cold water intake valve died. I ordered the replacement hot/cold valve a month ago but noticed, upon removal of the valve, that there was significant water drip evidence around the electrical valve solenoids. The water drips caused the valve to die. Drips came from a clogged injector hose air break directly above the valve. Replaced all hoses and water level vacuum air line. Very easy process. The front drops off with two screws. The lid is off with two screws. All hoses easy to R/R. It took about 2 hours to complete. All replacement parts were perfect. My belts are fine so I'm ready for another 30 years of service.
      17 of 20 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Leaking water
      The washer leaked only when i used warm or hot water. I found that the rubber injector valve would get to soft when using hot water,allowing the water to leak through and bubble out and onto the floor. I went ahead and replaced the injector nozzle, injector sleeve and the rubber injector valve. I ordered the parts monday morning and they arrived the next day. Excellent service.
      • Dennis from scottdale, PA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Pliers, Screw drivers
      • Parts Used:
        WP216201, WP215447, WP213015
      14 of 16 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Washer leaking from left side during fill
      After reading the description of the problem and finding the source of the leak I decided to buy the parts suggested.
      To begin:
      1. Unplug and turn off water valves at the wall.
      2. Unscrew the two front phillips head screws that hold the front of the machine on. Pull off the front facing panel of the washer.
      3. There are two hex head screws that hold the lid on. Remove these and then the lid can be lifted to see the nozzle and the valve.
      4. Unscrew the pipe clamp that hold the valve on to the pipe.
      5. Take out the old valve and nozzle.
      6. Use water or soap to lubricate the nozzle and valve before replacing.
      7. Install the new parts and reinstall the pipe clamp.
      8. Replace the lid and the screws.
      9. Replace the face cover and the screws.
      10. Plug in the machine and turn on the valves and test.

      I tested the machine and thought I could save the water and run another cycle later. This is a bad idea. The water fills up and over the top when a new cycle is added because there is no water level sensor. If you decide to test it and need to empty the water instead of wash a load you can turn the dial to spin and it will drain your test water.
      Best
      • charles from Davis, CA
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Nutdriver, Screw drivers
      • Parts Used:
        WP216201, WP213015
      12 of 13 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      7 Reviews
      4.7
      Filter By Rating:
      • 5 Stars
        6
      • 4 Stars
        0
      • 3 Stars
        1
      • 2 Stars
        0
      • 1 Star
        0
        Sort by:
        Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
          Model Cross Reference
          This part works with the following models:
          PartSelect Number: PS11738878
          Manufacturer Part Number: WP213015
          Brand
          Model Number
          Description
          Maytag
          A104
          Washer - Top Loading
          Maytag
          A105
          Washer - Top Loading
          Maytag
          A106
          Washer - Top Loading
          Maytag
          A106S
          Washer - Residential
          Maytag
          A107
          Washer - Top Loading
          Maytag
          A107S
          Washer - Residential
          Maytag
          A108
          Washer - Top Loading
          Maytag
          A108S
          Washer - Residential
          Maytag
          A110
          Washer - Top Loading
          Maytag
          A112
          Washer - Top Loading
          Maytag
          A15CA
          Washer
          Maytag
          A15CM
          Washer
          Maytag
          A15CT
          Washer
          Maytag
          A16CA
          Washer
          Maytag
          A16CM
          Washer
          Maytag
          A16CT
          Washer
          Maytag
          A17CA
          Washer
          Maytag
          A17CM
          Washer
          Maytag
          A17CT
          Washer
          Maytag
          A180
          Washer - Top Loading
          Maytag
          A181
          Washer - Top Loading
          Maytag
          A182
          Washer - Top Loading
          Maytag
          A183
          Washer - Top Loading
          Maytag
          A18CA
          Washer
          Maytag
          A18CM
          Washer
          Maytag
          A18CT
          Washer
          Maytag
          A190
          Washer - Top Loading
          Maytag
          A1910
          Washer - Top Loading
          Maytag
          A206
          Washer - Top Loading
          Maytag
          A206S
          Washer - Top Loading

          Get in touch, we're here to help!

          Open until 1am EST

          Contact Customer Service