MAT10CSEGL Maytag Washer - Instructions

Pulled the switch assembly cover off. Removed the screws that held the lid switch assembly on and replaced the assembly.
I just want to say that the online exploded view of the parts list was very helpful. I really needed pictures and your website had them. Also the service delivered my part very swiftly and ordering was easy. If I ever need appliance parts again I will order them from your website.

I tipped the washing machine (somewhat tricky since it sits under the dryer) and saw the broken belt. Went online, found the belt I needed, bought the set of two belts since I figured it would probably be a good idea to change both belts at the same time. After a few days I had the belts in hand; it took more time to jockey the machine back into place than it did to attach the belts. No tools necessary; the washer parts are on a spring. I did need a screwdriver, however, just to re-attach the washer's front panel.

Removed the cover on top raised control panel at back of machine. Checked fuse, then lid switch which were okay. Checked Check-lid switch which was bad. Ordered and replaced. I always take pics with cell phone before removing anything to see position, wire colors, etc. Only difficult because of location on check-lid switch. Hard to reach even with right angle screwdriver. Had to bend some of the metal housing above the switch to get screwdriver in there.

Changed lid switch. The hardest part was to remove the old switch. Wire connectors were very tight on the connection tabs of the old switch. Just out of curiosity, I did take the switch base plate apart just to see what the lid lever looked like underneath and how the adjustment worked.

Based upon my research on line and my 'hunch' I ordered the Lid Safety Switch for this old Maytag Washer. Got the part in good time and it was very well packaged. After having some difficulty in removing the one nut that held the old switch in place I installed the new switch, plugged it in and was delighted to hear the washer working like the old days. Now I have many, many loads of clothes to catch up on.

Replaced the air tube, existing one had been chewed by mice was easy to replace and solved the issue

Removed front of control panel on the washer. Found the lid check switch, removed one screw, leaving the wires attached and replaced the old switch with a new one. Removed the wires from the old switch and place them on the new one. Reconnected the machine to the outlet,,closed the lid and listen to it run.

Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top back out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3

Found main drive belt had a big chunk out of it. Both belts were worn and "gummy". Replaced both belts with belt kit 12112425; no tools needed -- belts are replaced from the bottom. Just tip the washer back to the wall, and there are the belts.. Installation time 5 minutes.

after checking obvious reasons (plugged in, breakers,) i took off control panel cover and saw that the fuse was blown, replaced it, plugged back in and it worked. After 1st wash was done, again it didnt work and the fuse was blown. I followed the wires from the fuse and they led to the lid check switch,which had a char mark leading me to beleive it was fried. I checked for continuity with an ohm meter(after disconnecting the power of course) and got no reading after pushing in the red button on the switch.I googled maytag replacement part and Partselect came up.Easy to understand ordering, and $20(including shipping,2 days later and about a half hour install, my machine was running

Done a troubleshooting problem online. Figured out the problem and ordered the part. Removed old part installed new part and I am a female not that it should make a difference but some would say it does. Had the old part out and new part put in and it took me about 30 minutes. Washer now works like a new machine. Very pleased and proud of myself. The part was the lid switch assembly.

Checked the fuse it was blown. So I replaced it, pluged the washer back in. pull the start knob that's when the lids switch sparked and blew the fuse again.
Found you on line ordered the complete assemble to save me from the trouble of slowly change each.
Switch out the wiring from old to the new assemble. Line it up, one screw and a little adjusting and the Maytag is back in business!
Thxs Guy for the quick shipment had it in two day on a ground shipment!

Looked online and found a video for the repair consistent with a water leak. Two screws to remove the front panel of the washer, loosen two hose clamps, remove belt (by hand) and three screws to remove old water pump. Replaced pump, replaced belt (made sure it was tight, but not too tight), replaced water hoses, placed cover back on the front and I was done. Maybe 15 minutes tops. Very, very easy. Works like a charm and saved probably $100 in labor.

Well I looked on line to see if there were any similialtys to my problem and followed what they had done on their washing machines. I replaced the water pump,the slide control below the motor,and the lid switch.None of these items worked.I called a tech.and he informed me that it sounds like the transmission is bad ,he is coming to my house tonight to take a look at the machine.

A friend said the cause was probably a belt. On Google we checked the washer model number which took us to your site. We looked at the videos on how to do the repairs, and so ordered a drive belt and pump belt. They arrived in two days. My husband is 84-years-old, I'm 83 -- difficult for us to lift the machine to tilt it. Experimenting with fulcrum and lever, we managed -- that's what took so long. After watching the videos again, I laid on the floor and was able to apply the belts. Washer works great!