MAT10CSAAL Maytag Washer - Instructions

I tipped the washer up on 2by4 blocks used 1/4 inch rachet with 5/16 socket two remove 3 screws and the belt from underneath. Took clamps off hoses yahoo saved l00 bucks!

To troubleshoot the problem I removed a panel/blank from the back of the machine. I then started to fill the tub while watching the pump. It immediately leaked from the shaft seal. I ordered the part early the next morning. It arrived late the next day. I was able to remove the front panel of the machine by removing a screw at each front corner of the bottom of the machine. The pump was attached with three screws which were simple to remove. The pump was an exact replacement and fit identically to the original. I tensioned the belt, and tested the machine. Before reinstalling the front cover, I cleaned the interior of the machine a bit and replaced a couple of hose clamps whose steel screws had started to corrode. All in all a simple repair.

This job turned out to be alot easier than I thought thanks to the tips I received on the web site. First I removed the agitator with a small nut drive I believe it was 1/4". Than I removed the two screws holding on the lid and lofted it out of the way. This is where the Hammer drill comes in. I had read someone else had used WD40 to help break free the threads and get the retaining ring off the tub it self. I worked on this for about 20 minutes with lube and trying to tap it off with the hammer and tap method. Finally I looked over and sitting there on the self next to the washer was my hammer drill. It can't be any worse than banging on the thing with the hammer. (They proably don't reccomend) but with a straight tip and a couple of quick shots the gaint nut came right off. I will say that my washer being older I could barely even tell where the threads were so I figured why not. It worked great. I then took the tub ring(plastic) at the top off and removed tub. Again a couple of quick shots with the hammer drill and the ring came right off. I did spend a little time making sure everything was clean and then reassembled machine with no more leaks. It may sound strange but it worked great with no fighting the space constraints, the calcium buildup and no damage to machine. If it doesn't work get a bigger hammer. Good luck

Pulled the switch assembly cover off. Removed the screws that held the lid switch assembly on and replaced the assembly.
I just want to say that the online exploded view of the parts list was very helpful. I really needed pictures and your website had them. Also the service delivered my part very swiftly and ordering was easy. If I ever need appliance parts again I will order them from your website.

Followed the directions posted by another user. His tips were very important and helpful. At first we only ordered parts where it was leaking, then decided we might as well change the remaining parts as recommended by the other user in his description. This is the FIRST issue we have had in 19 years of use. Ordered the parts, received them quickly and correctly. Installed them and it works like a new machine. This Maytag will probably last another 19 years.

Top came off quickly with socket wrench. Removed gasket in about a minute. Spent 45 minutes getting grime ( soap and lime) off of top. Took five minutes to replace gasket.

Haven't been able to get front back on. Clips go on side rather than top. Found missing clip for which new one was purchased in transmission. Still haven't gotten front to stay on. Clips keep springing out.

all went well until testing. tub level did not shut the water off, caused a spill

new replacement water pump leaked where plastic housing upper and lower halves were bonded, presumably with glue. As a quick fix I wrapped pump with some 3M 4411N sealing tape. Seems to have stopped or really slowed leak. I was going to get another new pump but now worried it will leak as well so going to see how long tape fix works..

Removed front door from washer lifted front of washer off floor and removed belt’s put washer back on floor
Removed motor and slide
Cleaned and replaced slides and greased put back in washer secured
Then lifted front of washer back up replaced new belts and started the washer up worked great put front of washer back on done
Great instructions that came with parts

Replaced the lid switch assembly, works like a charm.
10 minute repair, 4 screws for the front panel, one for the switch assembly. Be careful not to break the plastic tabs that hold the right side of the assembly. As someone else noted, adjust the assembly front/back in the screw slot so the switch activates properly for open/close.
Fast shipping, great price, thanks Part Select!

Remove the rear panel covering the control panel. Remove the two screws on each side of the upper control panel. The top removes with gentle (or not so gentle) taps toward the front of the washer. Lift the upper away but be careful of the attached wires. Top must be removed or switch cannot be removed as it cannot pass the cycle selector. Note the wire positions and colors to the switch assembly, remove them, and loosen the screw holding the switch assembly in place. Tilit assembly up like opening a book and lift up and away from the washer being careful of the lid switch actuator below. Replace with new assembly, making sure actuator is positioned to activate switches, and reattach the same screw. Reattach wires to appropriate places, replace top control panel and reattach screws, replace rear panel.

Well I looked on line to see if there were any similialtys to my problem and followed what they had done on their washing machines. I replaced the water pump,the slide control below the motor,and the lid switch.None of these items worked.I called a tech.and he informed me that it sounds like the transmission is bad ,he is coming to my house tonight to take a look at the machine.

Done a troubleshooting problem online. Figured out the problem and ordered the part. Removed old part installed new part and I am a female not that it should make a difference but some would say it does. Had the old part out and new part put in and it took me about 30 minutes. Washer now works like a new machine. Very pleased and proud of myself. The part was the lid switch assembly.

Disconnected the hoses , power cord, and the drain hose. Tipped the washer on it's front panel and removed the old belt and spun the new one on. Tested for tightness as per the instructions and sat the washer up and hooked everything up. Total time---5-10 minutes.
Local appliance dealer insisted this wasn't the belt we needed. Thanks to your website we easily selected the right one. Thanks.

Checked the fuse it was blown. So I replaced it, pluged the washer back in. pull the start knob that's when the lids switch sparked and blew the fuse again.
Found you on line ordered the complete assemble to save me from the trouble of slowly change each.
Switch out the wiring from old to the new assemble. Line it up, one screw and a little adjusting and the Maytag is back in business!
Thxs Guy for the quick shipment had it in two day on a ground shipment!