LSE7800ADE Maytag Washer Dryer Combo - Instructions

Old latch and door striker were pried out with a flat blade screwdriver. New components popped right in. Repair was less than two minutes.

I used two vise grip wrenches in place of specialized tool that is no longer available. I put the vice grip wrenches on the brake assembly and hit them alternately with a hammer. I also used penetrating oil.

Note, the parts package stated made in USA but the bearings had China stamped on them.

-determined problem
--verify that hose not clogged, screen filters clean then swapped cold w/ hot and verified that the problem was in the hot valve.
-Moved washer to get access to hot/cold valves
--opened access panel holding valve and swapped wires between hot/cold to verify that hot did not activate when it should
--Used voltohmmeter to verify that hot water valve had open circuit.
--Obtained replacement valve, installed, reconnected water lines and verified that hot and cold water worked.

The water valve on the cold side was making noise when cold water ran. I removed the screens but did not see a problem. I ordered a new valve and installed. The noise is gone and the water flow is back to normal.

At the time we did not realize the water flow had slowed.

The repair was very simple.
1. Shut off water and disconnected the water lines.
2. Removed screws holding water valve bracket to wash machine.
3. Disconnected electrical connections and water fill hose.
Installation was reverse of removal. The directions said to use a small piece of rubber hose that was included in the package, but it was not necessary. Double check for water leaks before finishing installation.

I'm a 70 year old woman. I followed all instructions provided by "Steve" from Partselect video. The video was very well presented and allowed me to fix the leaking problem myself. Watch the video...you can do it.

I was lucky to find a youtube video that showed every step. The hardest part was removing the front of the machine only because the screws were a little tough to access. Part replacement was quick and easy. It saved me approx $150.00

All I had to do is tilt the machine to expose the bottom and replace the belts. It was fast, easy and the machine works fine now.

Easy video on Parts Select, then it still wouldn't work. The fuse behind the panel was blown, replaced that. And it was hero dad, I expect the bad water inlet valve blew the fuse.
Good Job, thanks for being there.

Removed front cover, removed housing cover, took old fan off, installed new fan, put covers back on.
Your instructional video was very helpful. He told which screws to remove to get the covers off. I was unsure about how access the fan until I watched. Well done!

The instructions were clear. Did every step. Did 2 loads so far and everything works like new.

My washer is apparently 37 years old. I bought it used in the 90’s and have had to do little or nothing to it repair wise. It started to make a loud squeal/squeak when the spin cycle stopped. I watched a couple videos showing the brake assembly, bearings and belt replacement and was able to find parts. However, one bearing appears to no longer be made (just repacked with heavy duty grease) and the special tool is nonexistent. I read others using a chain clamp vise to remove the brake assembly and bought a 20 inch chain clamp vise and a 3 set variety of vise grip pliers for about $20. They make an 18 inch chain vise but glad I got the 20 inch. I used two vise grip pliers to clamp chain around notch two notches that the specialty tool would normally grab. It was a cumbersome getting in there to whack the pliers with a small sledge hammer so I got a approx 18 inch 2x4 and cut a notch at the end to keep chain vise from digging into bottom of washer and whacked the end of the 2x4. Seemed to work ok and did the same to tighten back after replacing break assembly. Got it out back together and no more squeal.

I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.

Removed washer tubs inner and outer nut (part # 10 ) on inner was hard to remove and is a reverse thread used hammer to loosen once off removed 1st tub - then removed set screw #17 and then unscrewed mounting s item #29 this again required some hammer tapping to loosen - once off used flat head screwdriver to pry & remove the rubber piece on bottom of outer or 2nd tub -but keep going as the leak will probably be from part #20 tub bearing ( this will save you the time to test and find out it still leaks and have to take apart again after only replacing #29 removed 3 bolts holding tub - disconnected hoses and removed 2nd tub - used rubber hammer to knock out and install #20 tub bearing - reasembled and wow no leaks to cost about $120 - time worked on 3 hrs - only because took apart 2 times - down time on washer 10 days as we didn't order all parts to start with no beer needed but did enjoy a nice red wine - good luck

First I shut off the power at the breaker. I removed the two screws on top holding the front panel in place I removed the wires carfully marking so they would go back in the correct places. I removed the tub and then removed the old motor and switching the wires to the new one. Mounted the new motor, replaced the tub with the belt, attached the belt to the motor. connected the marked wires and put the front cover back in place with the two screws on top of machine. Turned the power back on and started it up it works perfect The motor only cost $119.00 and a little of my time much better than getting a new machine as it is a stack washer dryer.