LCE732LL2 Frigidaire Washer Dryer Combo - Instructions

popped the catch in existing hole and replaced the screws

So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.

I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I used a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.

After struggeling the most with lifting out the inner drum and then the wash drum. I realized when the job was complete a better way. 1. Take the top off the washer. 2. take the front off the washer. Then disconnect all wires and hoses from assembly One small hose on the tub and the pump hose at the bottom. 3. at the bottom of the overall assembly there are 3 braces holding the tub assembly with 2 springs on each brace. Go under and remove the springs and then lift the whole assembly out into the middle of the floor. 4. remove the top cap off of the agitator. 5. remove the agitator. 6. if you are lucky and the bolts are not seized in the block that holds the shaft remove the small steel block from the bell and remove the bell. 6. Slide the inner tub up and off the shaft and again if all goes well the outer wash tub should slip up off the shaft as well. 7. remove the drive belt from the motor and transmission.

replaced bearing and shaft new belt and everything works just fine

After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.

Purchased both the belt and idler pulley. Bought the idler pulley "to have it if it were needed" since it was only a $15 part.

Watched two videos provided on PartSelect for our model number with our symptoms. Both showed an easy access of idler pulley at the front of the washer. My emailed invoice also contained links to the video for each part.

Getting the panels off went exactly like the video. However, the idler pulley was nearly on the back side of the tub assembly/transmission and NOT easily accessed as shown in the video.

I replaced the belt and ran the washer without replacing the idler pulley. Since it performed very well agitated/spun I elected to avoid the daunting looking task of idler pulley replacement. Hung it up for "just in case" future use....again not hard to do at only $15.

we took the hoses off then unscrewed the bracket that was connected to the part and then once out we put bracket onto the new part and screwed it back to the washer connected the hose back and WOW the water was flowing

I looked up the repair on You Tube and it looked easy! Take off the top of the machine (unplug and disconnect water first), 2 wire connections and 2 screws to mount. The only problem I had was screwing the mounting plate on the machine. It needed some help enlarging the hole a tad, I used an awl. Reconnect the water and plug in.This Granny rocks!

Replacing all springs. Able to replace 2 short springs and front spring. Can't get to ones in back of washer tub. Unable to use strenght in arms to remove old springs. Help videos were great. Saved money by doing repairs myself.

Remove top cover and front and remove drum and install a new bearing kit and new belt.

Watched Video Provided. Very Simple Repair. Asked my lovely wife to hold drum in place while replacing drive belt. She gladly complied and is back doing what she seems to love most. And no, I'm not kidding. Our washer and dryer seem to run 24/7/365. I've completed various repairs on both appliances over the last couple of years and saved 100's of dollars thanks to this site .

Poped up top, removed front pannel (2 phillip head screws) observed failed belt. Replaced belt. Tensioner can be held back by hand so it was easy. Works great. Part Select Rocks! I put in the model number and bam, there was my needed part, 3 days later it was in my hands. This was after me wasting time driving around town trying to find it at home depot type stores to no avail. I'll never do that again. This website makes repairing appliances a snap. Gotta love on-line shopping! woo hoo

Just like in the video, but with a stackable washer/dryer unit, works like new now....

I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you