Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
oven light kept burning out instantly
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy
I determined the bake igniter was not working. If the bake ignitor does not work, the sensing unit to turn on the gas does not activate. I examined the bake igniter it was blacked significantly in one spot. There were no apperant cracks in it. I did a web search for the part and ordered it. Three days later it was delivered. Take pictures of each step if you fell the need. Pull stove away from wall turn off the gas, unplug power cord, remove panel in back of stove that covers the electrical, unplug the ignitor/element. Move to the front of the range and remove the oven rack. Remove the cover over burner tubes, it secured with several screws. Remove wing nuts for heat shield. Carefully remove burner tubes along with the attached ignitor/element. You will have to carefully guide the ignitor wires out with the burner tubes. Unscrew ignitor from the burner tube, attach new ignitor/element. Reverse the steps.
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
unscrewed screws in the back of the stove. inside the stove, replaced the old bake igniter with the new one and connected the electrical wire in the back of the stove.
very simple fix. I removed the bake burner cover (the blue cover on the bottom of the oven), under that is the oven baffle which is held on with one wing nut and removed that. Then remove the oven bake igniter screws(two on the side), remove the orifice cover scew and remove then remove the oven bake burner gently. once these parts are off you need to remove the screws on the back of the oven ( I believe theres about 4 or 5 along each side and there are 4 on the bottom of the large metal plate. you only need to remove the large metal cover every thing else stays put. Disconnect the lower back burner attatchment which just clips into the connecter. once thats removed the part should come out easlily from the inside of the oven. Now take the new bake ignitor and feed the wires through the opening on the inside of the oven that allows the wires to come through to the back of the oven(you may need to feel around for the wires and move some of the insulation aside to feel them) once the wires come through the back connect the new part by clipping it to the harness the old part was removed from. At this point you should be able to reassemble the back of the oven exactly the way it was removed.Now go back to the inside of the oven, replace the bake burner gently over the bake burner orifice and put the orifice cover back on and reattach with it's screw. Position the bake igniter back into place on the side of the bake burner and replace the two screws previously removed. Once thats in place its time to put the oven baffle back on and secure with the wing nut and the last step is to place the bake burner cover. Just set the oven to bake and it should be working if thats in fact the problem..Good luck. Took me less than 15 minutes to fix.Some find it easier to remove the oven door but I didn't need to do this since I had enough room to access the front and the back of the oven without any trouble.
