KER331ZAS2 Frigidaire Dryer - Instructions

Taking off front of and top of dryer and panels on the back. Releasing the belt and taking out the tube un screwing the two pieces off the back of the machine putting new ones in and putting belt back around drum and setting drum in. Then holding drum while the front is put back on then attach top and a couple panels on the back.

I opened top section with a screwdriver, pushing in the release.
I opened front panel with door with screwdriver pushing in the release.
I lifted drum out through the front.
I replace the Idler Arm assembly.
I greased the rear drum bearing race.
I vacuumed out and cleaned blower and dryer area.
I put the new belt on the drum, reinstalled the drum.
I put belt around drive motor and Idler arm assembley.
I put front panel with door back on.
I put the top panel back down and snapped into place.
Tested dryer, job done!

You simply pry the old handle off with a flathead screwdriver, and then line up the new handle and snap it into place. It took less than 30 seconds! A breeze.

so easy my daughter installed it the video was very helpful

Once the part arrived, I logged back into my order and watched the part installation video as I did the repair. The video was perfect, it made doing the repair easy and safe. Best part is I didn't end up with any extra screws which was good.

The repair went very well for a 1st timer. Instructions were very easy to follow. Thanks

remove 2 screws rear of drier at top slid the top back and off removed 4 screws on front electronic read out panel and disconnected two wire harness plugs remove the panel removed 2 screws for lower panel at top on either side of rotating drum,tilted machine back removed two screws at very bottom on front of dryer to remove lower panel ,and remove the lower 2 screws to remove front panel.lifted rotating drum up and out of drier ,removed 4 wires on the heating element and four retaining screws from rear of drier to releases the heating element,than reverse the procedure for assembly.

Remove drum, replace belt, return drum

I unplugged the dryer from the power outlet and removed two screws from the back of the top cover and removed the cover. Then I laid the dryer down on its back for easy access to the screws on the bottom of the front side. I then removed two screws from the front bottom cover to clear the way for two more screws for the front main panel and door. Then I removed those two screws that attach the front panel and door to the dryer from the bottom of the dryer front. I then stood the dryer back up on its 4 pegs. I removed the top 4 screws connecting the control panel to the cross bar on top. Then I removed the two screws from inside the dryer accessing them from the top of the dryer, holding the front panel. With little and gentle force I pulled the front panel and door from the dryer housing, making sure not to loose the 4 snaps that come off with it. I removed two screws from the access panel to get access to the pulley in the lower back of the dryer. I loosened the tensioner by pushing it to the side and pulled the belt off the pulley. Next I needed to remove the drum which is connected by three screws in the center of the inside of the drum to a small plate on the outside that is attached to a ball that goes into a grease box. I then wiggled the drum out of the dryer. With some force I pushed the plate upwards to disengage it from the grease box and removed it. I unplugged the electrical wires connected to the thermostat and element. I then removed 4 screws from the back of the dryer that hold the heating element housing and removed the housing. I replaced the heating element and housing and the belt and put the dryer back in reverse order.

took front panel off, removed access panel in rear to disconnect the belt from motor. removed top panel (this is a stack unit) take plastic rivets loose from lint trap, remove lint trap tube, pull drum out after slightly pulling up to dislodge drum from bearing cradle, Remove bracket and bearing from back of unit, clean parts of old grease (be carefull not to loose small ball bearing on back) Reassemble parts using moderate amount of new grease, put parts back together in reverse order.

First I watched the video available on the web site. After watching the video, I knew exactly what to do and how to do it. Really made the job a lot easier than it would have been. Some steps were harder to do than the video made them look but I atribute a lot of that to the fact that they were working in a large work shop and I was working in an area not a lot larger than the dryer. The hardest part of the job had nothing to do with changing the element, it dealt more with getting the vent hose off and on. Who ever designed the connection apparartus on dryers, used to connect that stupid hose to the back of it, must know something I don't. I have never had any luck when it comes to being able to get the hose connected and then getting the dryer back in the hole it came out of, without the hose falling off or getting crimped. PartSelect is a great company to deal with. Ordering was easy due to the highly intuitive web site and I got the part in two days. Saved me a lot of time running around town, burning a bunch of gas trying to find find what I needed. Thanks

The part fit perfect repair was simple thank guys for your help u are the best/removed the top/ front face /belt & drum removed old element installed new one dryer works perfect thanks again

I youtube'd the repair, and repaired it! While I was at it I replaced the belt! (Highly recommend replacing the belt while you are replacing the element!) Was a snap!

Had the drum bearing but had never got a round to putting it in we just let it squeek. Then the belt went. Easy enough, whatched the tutorial once and just did it. 35 minutes and back drying.

I never respond to any of these surveys, but in this case ill make an exception because they made it so easy and parts were received correctly a quickly. Thanks, dan