KBLS20EVMS00 KitchenAid Refrigerator - Instructions

Remove crispers & bottom drawer. Removed glass piece. Unscrewed piece( small nuts not screw heads) There is also a nubbie at front. You must remove by sliding out & lifting back of part. Reuse screws to replace piece & drawer runner. It took 15 to 20 minutes. I am all thumbs. If I can do anyone can do!

This kind of repair makes me love the internet. Thank you. Follow advice of my fellow posters but beware, all your plastic parts are very brittle from the cold. Proceed slowly. As mentioned by others but worth stressing is...do resist the temptation to force any piece...I could just see myself snapping one of these pieces and having to order another part! Take your time to work out the sequence to disengage each piece in turn. It's a bit of a puzzle but take your time. Also suggest starting the job with a nice bowl of warm baking-soda water to gently and effectively clean everything as you go.

removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self

I initially tested the heating element and defrost thermostat using an ohm meter. the defrost thermostat was incased in ice, so I replaced it first. The refridgerator worked for about a week and then froze up again. I then replaced the thermistor and the unit is working as designed.

Unscrewed all related parts and also took out drawers and glass shelf. Reused plastic slider which raps around right corner to the back wall of the unit. Make sure to remember how this plastic slider fits into the new end cap, it is a little tricky putting it back without cracking it. Suggest take a digital picture as to how it fits together before taking the slider out of the old end cap. Reinstall same way as you took it out. Good time to clean while everything is out of the bottom of the refrigerator.

This was the third icemaker replaced since January 1999. Improvement need to be made in the design of the icemaker so that more than 2-3 years of life is available.
The most difficult part was disconnecting the power plug in the back of the icemaker. You must squeeze the upper and lower tabs together and pull out at the same time to disconnect. Once this is done, take out one nut head screw, lift up on the icemaker and remove from the hanger. Be careful that you don't break the plastic tabs on the hangers. Replace new icemaker in reverse, feed water supply where it must go in the back, resnap onto hangers, replace the nut head screw and snap in the power plug. It took about 2 hours before the icemaker began making ice. It has been working fine ever since. PS. I saved about $200.00 over having a repairman come in and replace the unit.

Took out the drawer and upper rack out of freezer removed back wall from freezer took out fan motor housing and replaced motor and thermostat. Works like new now.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Removed the 3 screws that hold the ice maker in place and remove the cover and level wire. Put the cover and wire on new part and install the 3 screws. Had ice within 1 hour. A very easy job for the do it yourselfer. Suspect the heat coil that melts the cubes was not working in the old unit and cubes stayed in the tray.

Simply cut the water tube on both sides of connector and push in the new one.

Pulled the unit from the wall, and unplugged, and turned off the water. Removed the back plate at the bottom of the refrigerator to gain access to the water inlet valve. Disconnected three tubes and two electrical connections and reconnected to the new inlet valve. Reassembled the back plate. Then turned everything back on and checked for leaks. Re-Installed the back plate. This was a fairly easy repair. The only problem I had was getting the water lines off the old valve. It was a bit of a struggle for me. I did watch a couple of you tube videos before I got started.

Remove lower freezer door from mounting frame (4 screws). Remove inner shelving and shelving brackets, Total of six screws, three on each side on lower brackets and 4 screws, 2 on each side on upper brackets. Remove ice cube maker (4 screws). Remove thermometer frame from back cover and slide thermometer out of frame. Remove 4 screws from back cover and remove cover. Slide thermometer through hole in back cover. Remove 4 screws from evaporator motor housing. Gently pull plastic fan off of motor shaft. Remove motor from housing and install new motor. Reinstall all parts in the order removed.

Replaced the relay and capacitor it runs.

First I checked to see if the water pump in the base of the refrigerator was working properly. To do this, I removed the water filter, placed the by-pass cap on the water filter head, and dispensed water. The dispenser worked very well so I knew it was not the pump. I had just bought a new filter so it was okay too. So I figured it was the Water Filter Head assembly. To install, I followed previous advice on Part Select website and followed a YouTube video that was excellent (enter "Refrigerator Water Filter Head and Tube Assembly-How to replace). Best advice...Styrofoam block that inserts from back of refrigerator where tubing enters...when removing, push it out from the inside of the refrigerator to avoid breaking it into pieces. Other good advice, unplug refrigerator and turn off valve to icemaker and water dispenser. Easy repair, could do it in half the time now because I was very careful when installing this item. Results: Excellent flow from dispenser!!! And better ice cubes too! Well worth the effort.

I brought you the exploded view of the crisper parts on your website and proceeded accordingly. Besides the three nuts holding the end cap to the frig interior wall the temperature adjustment linkage had to be disassembled on reassemblied on the new replacement end cap. Plastic linkage parts present the problem of breakage, so one must be careful during the disassembly process. Some other type of fasteners for the linkage assembly (screw and nut, ball and socket) would be prefereable. All and all, its a machine. Wtith exploded view, what could go wrong?