KBFS20EVBL00 KitchenAid Refrigerator - Instructions

I called the installer of my filter unit and he told me that often, thhe fridge filter is the problem. Like magic it worked

i had used your web site before and i read several problems that your readers had. i went to the back of the unit, removed the bottom cover and right there the i found the run capacitor and i chaged it. since i had only ordered this part to save money i went back and ordered the Start Device which when i took it off it was completely burned. the replacement part came labeled with 2 different compressor #, so i picked the one that i had and unpluged each wire. the part may differ from the one that it's in the unit but it worked when i pluged everything back on. it also helps to take a picture of everything before removing the wires in case you have to leave it and come back later. i hope to use this refrigerator another 10 years. thank you all for your help.

first pressed in two bottom corners then used fingers to press in bottom section,pressed in two top corners then pressed in both sides using fingers followed by pressing in top section using fingers.VERY EASY !

Pulled out on gasket seal at top right corner of door and when loose pealed the seal out around door. Installed gasket by inserting channel insert into door groove and pressed gasket in while lightly pulling down to stretch seal out to facilitate inserting gasket lip into door channel. Bada bing! Done. Good fit. Note: I laid out gasket in the sun to soften it up as there were some small wrinkles in material from being folded for shipping. Hair dryer would work too!

Watched installation Video on the website parts. I put the new gaskets in bath tube in warm water for a few minuets until the gaskets were warm and pliable. I removed old gaskets cleaned door facing and installed new gaskets as instructed on video. Thanks for the information on how to install because I was dreading trying to do this task. "Just follow and listen to the instruction on Video".

Remove the existing mullion rail:

- Remove the screw from the center hinged cover.
- Remove the mullion rail by pushing upward. The top and bottom hinges slide over tabs attached to the door. I had to bump it gently from underneath.
- Disconnect the three wire connector that's underneath the center hinged cover.

Install the new mullion rail by reversing the above steps:
- Connect the three wire connector and snap it into its holder.
- Slide the new part over the top and bottom hinges. Be sure that all three hinges are correctly lined up before sliding the rail over the tabs.
- Push it down far enough that the hole for the screw in the center cover is lined up with its corresponding receptacle in the door.
- Replace the screw.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Removed the middle screw and the whole rail came of. Unplugged wires and removed old rail. Plugged in the new rail and slid top and bottom slides on and put on the middle screw. Job finished

Had to disassemble ice maker to install part. . .

Removed the three screws that held part, lifted and removed old part and replaced with new piece.
Couldn't have been easier. Saved me the $100 the repair man quoted me. Cannot believe it was so easy and the
part was soooo affordable! Thank you very much for the speedy delivery. It came within days of my order.
I will use your service again for sure!
Thank you!
Allyn Rosenzweig

1. removed both bottom crisper drawers
2. removed glass shelf under crisper drawers
3. removed shelf support pieces
4. removeded snack drawer
5. removed left slide rail using phillips screwdriver (2 screws)
6. removed LH end cap using socket wrench (3 screws)
7. attached new LH end cap
8. attached slide rail
9. installed glas shelf supports
10. installed glas shelf
11. install bottom crisper drawers
12. install snack drawer
13. install snack drawer top

total time was less than 15 minutes

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

you need to take the deli drawer out, make sure your flat head screw driver is large enough for the head of the screw as screwing into the plastic is a bit difficult. Other than that there are 2 screws and its pretty easy.

Removed old starter and capacitor as per your website instruction.
Plugged in new parts.
Compresser turned on

(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed