KBFS20EVBL00 KitchenAid Refrigerator - Instructions

The old gasket peeled out easily. No tools needed. The replacement gasket fit right in the groove. I did not need to immerse the gasket in warm water or use a hair dryer. Nifty trick: once the new gasket is in place, close the freezer door. Run your finger in the center groove of the gasket, which will push the magnet against the fridge. Leave the door closed for an hour. The gasket has then assumed a perfect fit and will continue to fit perfectly.

Awesome! Couldn't ask for it any better. I watched the video from Partselect multiple time and was just as easy as they said it would be. It took me longer to watch the video four times than it did for me to install it. I have a habit of 10 minute projects turning into a couple hours and this took about 10 minutes. Thanks.

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

unsrewed the back plate, removed three tubes. Then I removed old valve and replaced with new. Pluged two harnesses back in the new valve. Truned water on and checked for leaks and operated the filtered water tap and the ice maker. All went well.
I really like your site for the pictures included with the part, I like to see what I'm ordering.

The video was a great help. I was able to replace gaskets on both doors with out taking them off and no tools were needed.
One of the refrigerator doors has a plate that closes with the door that makes replacing the gasket questionable but I was able to do it with no problem.

1. Remove all drawers {3}, shelves {glass 1}, shelf support {1}. 2. Remove two {2} screws from End Cap. 3. Carefully remove End Cap and drawer temperature control part on the back wall keeping them aligned as installed. The part on the back wall swings out so that the tab on the left end of the piece may be withdrawn from the securing slot (hole). The two parts should be carefully removed while keeping the two parts at a right angle the way they are installed. The reason for this caution follows. 4. On the back side of both parts are plastic pieces that, I believe, can be easily broken if you are not aware. The pieces are connected together at the right angle. They are the control arms for the temperature control -- on right side End Cap only -- the left side doesn't have them or the rear part on the back wall. 5. The pieces must be disconnected and removed. You must examine and ponder how they are held in place and hooked together in order to disconnect and remove them without damaging them. The same advice is applicable to reinstalling the pieces in the new part -- End Cap. 6. After reassembled and keeping the two parts at a right angle, insert the tab on the left end of the back wall part into the slot (hole) and swing the two parts back into position. 7. Replace the screws. 8. Done, reinstall the shelf, shelf support, and the drawers. NOTE: I ordered the two screws but they were not needed.

First, make sure you have the correct part. I had trouble with mine, at first, until I realized that I had received the wrong part... it was same shape but larger. To begin, remove both fruit/vegetable drawers. Remove deli drawer. Remove deli drawer glass panel with both supports. Remove 3, 1/4" hex screws that attach end-cap. Disengage temp control slide and arm from end-cap by carefully moving parts in the direction where they will disengage. Remove temp control slide from end-cap. Now that end-cap is out, remove 2 screws that hold metal drawer slide to end-cap. Attach drawer slide to new end-cap. Attach temp contol slide and connect the plastic arm. Attach end-cap to refrigerator. Replace glass shelf, supports and drawers. Done.

I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning on the water supply and bingo...lots of ice cubes.

Popped off the control panel at the top behind the door. Found the thermistor and replaced it, cutting the wires and splicing the new one in. Immediately the warm section of the refrigerator was getting below freezing temperature readings, so the cooling vent was not opening. I put the old one back on and the temperature readings went back to being accurate. So this was not the problem. I believe now that the fan somehow is not blowing enough cold air up. So now I'll probably buy a fan motor and maybe a blade and try that. Otherwise the computer module I priced at $500 so I hope it isn't that. I replace the fan motor a few years ago already.

Unscrew filter. Screw on filter bypass

Replaced the left side endcap for the drawer. Three screws and it popped out. Easy process once I actually looked at it. Drawer cover now works as designed. Replaced inline water filter. Not problem there.

The repair was very simple, you just remove the existing part that is held in place by two holes in the lid and insert the new lid. very easy.

.screw held in the center of the rail,pull it out,slide the rail up off the support brackets on the door,unplug the old one & plug in the new one,slide on, & replace the screw! That Easy

Removed the door and replaced the broken door closure bushing. I had courteous help and responce from Parts Select people. Excelent turn around time on parts delivery.