JSS28WKW General Electric Range - Instructions

Originally the burner had a hole burnt through it, which resulted in a hole being burnt through the bottom of a pan. I replaced the burner and it would not heat up. I removed the top control panel, after securing power to the stove outlet, turned the power back on checked both sides of the swith with a meter (with the switch on) and had no power on one side. I went to two stores that did not have the switch in stock and ended up ordering from this site at about half the price! It arrived a couple of days later. I marked the wire colors on the old switch, took off the knob, removed two phillips head screws, pulled out the old switch and installed the new one and I was back in business. The hardest part was getting the sheet metal / heat gaurd positioned right upon re-assembly. To remove the panel there are two screws in the rear (nut driver) and a screw on either side of the front under each corner that require a torx driver to remove.

After reviewing the potential causes for the error code, I decided I'd try to change out the temp sensor. Using the ohmeter, I saw the difference immediately between the old and new sensor. The sensor is accessed from the back of the stove, and must be slide out to gain access to the rear panel. Since the stove I have is a built in, removing the stove and the access panel was the hardest part of this repair. Resetting the glass control panel was also a bit tricky to calibrate the touch sensitive buttons. Good luck.

The draw pictorial was not very clear. I orderd the two rear supports for the over storage draw, not sure they were correct.
They were correct and the design had been upgraded to add strength to the support.
The draw is now operational..better then ever.

took of the back panel with a nut driver,pulled off the wires one at a time ,put them on the new switch in same position as the old switch.removed old switch with a screwdriver ,screwed in new switch,replaced back panel,put on switch knob

Parts ordered from Part Select arrived 2 days! after being ordered even though we selected standard shipping.

Old generic poorly fitting bowls were removed, replaced with correct GE chrome bowls from Part Select, changed out 8" surface burner and it feels like we have a new stove! It looks great. All the surface burners fit perfectly into the new chrome bowls.

I will definately be using PartSelect. for all my appliance repairs.

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

lift door off and remove racks take out old sensor. one word of advise when pulling old sensor out tie a string around connector coming out of oven if it slips out of yor hand it could fall through hole iif you dont have a string attached you pull the whole oven out of wall to acess it

Removed back panel screws, removed back panel, removed screws of the control board, remove control board, heated glue and tore off plastic face plate, placed face plate on new control board, installed new control board, moved wires from old control board to new control board, test out oven, reinstalled back panel

Removed the screws holding the back in place, then pulled off the control knob and removed the two screws holding the infinity switch. Swapped the leads from the old to the new switch and reinstalled everything. Worked like a champ!

First I unplugged the stove, then lifted the stovetop, then took off the top panel on the back and disconnected the two wires. Then unscrewed the terminal block and put the new one in its place. Lowered the top inserted the eye and replaced the back panel. Works great!

This is the second time in a few months that I replaced this terminal block, so I made sure the contacts were clean and smooth. I also made sure the contacts were completely inserted in the block.

Very simple. Remove one screw and carefully pull the sensor until you see the connection point. Remove the old one and snap the new one in and guide the wire back and reassemble the screw. Be sure to remove the oven door for easy access.

Some of the original TO-9 switches were fused by the heat. I made them functional again with a cutter on a rotary tool, but to make the repair properly, I ordered the new control unit and the faceplate graphics. Note the guide tabs at the bottom and right edges when replacing the graphics. Don't plan on reusing your old graphics (unless you are a wizard at removing the very strong adhesive).
To gain access to the part, remove the 2 screws (part 715) in the bottom of the control assembly with a stubby screwdriver. Using a nut driver, remove the two screws (part 1000) on the back at the corners, being careful not to drop them behind the oven. Pull out at the bottom, then move the whole unit toward you. Note the position of the wires. A digital photo can help here. Remove the wiring and 4 screws holding the clear plastic TO-9. Put the screws in the new unit in the same holes and rewire. Put the assembly in place top-first and align the screw holes. Finding the same thread placement for the lower screws can be tricky, so start them gently.

unplug stove first...take back of stove off to get to burner switch remove wires colors coded.. get new switch put wires on the same way.plug stove in test burner...very simple to replace.and save $$$$$$$$

Unplug stove first. Raised the stove top and propped up useing wooden spoon and wife assistance holding up. Pay attention to spot brackets hand to top. Removed sheet metal screws from bracket clamp holding burner in place. Removed one extension bracket from old burner and transfeered to new burner. Removeing one bracket clamp allows the other one to act like a hinge and make for easy removal and replacement. Back of burner had corresponding numbers which made it easy to replace brackets in same place as old. I carefully take one electrical wire at a time from old burner and transfeered to the new burner. Replaced burner same way it came off.

Tried GE onoine parts department first and ordered the wrong part, then tried the customer hotline and they referred me to the right part but didn't explain that the design had been modified (the drawings had not been updated). I found an explanation on Part Select AND the parts were cheaper. Part Select sent the part, the necessary screw, and an appropriate instruction manual. Each support took less than a minute to screw in with a socket wrench.