JRP03006 General Electric Range - Instructions

First, I turned of breaker for the appliance. Removed two hex head (1/4") screws that hold element in place at back of oven. Gently pulled element exposing wires connected at base of element by hex head screws. Removed the screws and olf elelemt, placed new element in place, tightened screws, inserted into base and tightned screws for plate that holds element. After turning on the breaker, I set the oven to a low temp so I could feel the heat without burning my hand and was satisfied that the element worked.

as you explained in the e.g.
it was the easiest thing to do for my husband, and in 10 minutes I was able to bake again.

Thanks so much for the fast delivery!!!
Sincerely Rosemarie Ressel

Removed two screws that held the element flange onto the back of the oven, then two more little screws that held the element tips to the wires in back. Installed in the reverse sequence in about 10 minutes. A whole lot cheaper than calling a repairman! Thanks, the PartSelect customer service lady was a great help in getting me the right part for a 20 year old oven too.

IT was fast and easy! Thanks

The repair was a snap! Unscrew the two small bolts holding the back of the element in place. Pull out the element so that the connectors and wires are accessible. Unscrew the two wires from the element. Remove old element. Place new element in oven. Attach the two wires to the new element (two screws), place the new element in position and replace the two small bolts that were removed at the beginning. All done. Best thing? This is a 20 year old oven, GE didn't even have the part I needed. You did! Thanks.

After checking the website, I wasn't sure the part I needed was available. Called the Customer Service number and the lady was very helpful.
My part was delivered in 2 days regular UPS.

The most time took finding which breaker shut off the power to the oven. Removed two screws on the inside of the oven at the back wall. Pulled out the wiring and removed two more screws that attached the power to the element. Replaced the old element with the new one. Reversed the process. Done in 12 minutes! Very easy.

Used nut driver to remove old element and screw driver to remove power leads. Reversed process to install new element. Took about 5 minutes.

Took out the old (removed 2 screws holding the element to the back of the oven, disconnected the 2 screws attaching the electrical wires to the element). Decided to clean the oven with EasyOff. It took longer to spray this on, and then later wipe it up, than the repair itself. Reversed the procedure for the new element. A very simple repair - my wife is amazed!

Removed access screws from bake element cover, removed screws retaining wire connections on bake element, reverse procedure, and heat to burn off contaminants.

The longest step in the fix was the walk downstairs to turn off the breaker.
1 nut driver to remove the element from the oven. 1 screwdriver to disconnect. Just as simple to re-install.

If you have this oven I seriously recommend the $30 expense to replace the element before it fails. It honestly went out with a white hot welder's torch sort of short circuit that could have burned my house down.

I have to admit that I tried to remove the element myself but I did not have the right tool for the last two screws. If I did it would have been very easy. I ordered the part and had someone else put it in so I cheated.

Getting the part out was easy. Turned the power off (of course) first. The outside nuts were corroded, so had to use a pair of pliers to get them off. The inside connectors were easier to get off. I had a little trouble getting the connectors on the wires. The metal part on the heating element kept wanting to bend. I finally had someone hold that in place while I made the connections. The outside screws were easy to put on. The oven now works great. I think the element was failing over a period of time, and we just didn't notice. I can't remember the last time I actually saw the element get RED hot. Works great. Thanks for your quick service and reasonable prices. Will definitely use you again, when I need parts like this. (You are now Bookmarked on my computer).

unscrewed the broken one and replaced it with the new heating element. Worked perfectly! 20+ year old oven.

Unscrewed old element and screwed in the new one.

Removed two small bolt screws that held the bottom burner in place. Unscrew the two small screws that attach the oven wiring to the bottom burner. Put the bottom burner back in place and screw the two small bolt screws back in and its done.