JRP03006 General Electric Range - Instructions

I removed the two screws that held the element in place. I pulled out the element and disconnected the two wires and unscrewed the screws and then place the new element to it. screwed the wires back to the element wires and then push it back in. Replaced the outside plate and screw the two screws back in.

Save myself money by doing it myself.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Turned off circuit breaker, took two screws out to be able to pull element out from back. Took two more screws out to remove old element from oven. Did the opposite to install the new bake element. Turned power back on, and it worked fine.

Had my youngest son removed the two nut screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Removed element and installed new element in reverse order.

My husband removed the old element by shutting down the power, then unscrewing the element. Then he screwed in the new element and turned oven on for 5 minutes to break it in.

Very simple and so cheap!

Unplugged fridge.Removed 2 screws holding a panel. After panel removed took off old fan and inserted new. Quite simple.

If the bottom heating element is not glowing red when you turn the oven on replacing this part may be the answer. Look for a spot on the old element that could indicate it has shorted out and no longer carries a charge.
Very simple to remove the two screws holding the element in place, pull the element out about 3 inches, disconnect the two wires, replace with the new element and reattach the two screws. Simple and effective. The new element is fast and responsive. Do this before any other suggestions to replace more complicated parts in the thermostate etc.

Removed 4 scews from old element and replaced the old element with the new element with the supplyed new screws. It was very easy. The new element works great.

remove 2 screws holding element to oven back wall/ unscrew wires from element/ new element install the reverse of removal

Turned off circuit to oven. Unscrewed two screws holding element in place at back oven wall, pulled out old element and loosened nuts holding it to wiring. Discarded old element. Put new element in place and re-attached nuts to wiring (very simple). Pushed back into place and replaced screws to hold plate to back of oven wall. Turned circuit back on and put oven on to bake to test -- voila, success! Thank you PartSelect.com!

The replacement was simple. I turned off the power to the oven, took out two nuts holding the element in place, unscrewed the element from the power and finished the job in 10 minutes. The company that we called was going to charge nearly $200 to complete this job. I saved a lot of money by doing it my self.

Used a nut driver to remove two hex screws holding element to the back of the oven and then the two hex screws connecting the element to the oven wires. I pulled the element out and reversed the process. I turned the oven on and made sure the element worked.

First I shut off the circuit breaker for the oven then removed the screws that hold the element in place. The element was pulled out about 3 inches and unscrewed the 2 screws to disconnect the two wires. Upon receipt of the new element, I simply reversed the above process and the oven performed like new. Very easy, very quick and very grateful to have the oven operating again and it was a very inexpensive fix.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires
the Replacement fit easily. Part was delivered the day after ordering even though I used normal delivery. Oven broke on a Thursday,ordered the part Friday morning, back in operation on Saturday

Removed screws from plate holding the element in then removed the screws from the wires attached to the element. Reversed the process and was finished. Oven is back in working order. (I am recently widowed and this is the first time I have had to do this type of repair)