JGP933CEK2CC General Electric Cooktop - Instructions

Gary from HENDERSONVLLE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Igniters would not turn off

Replaced starter switch harness as well as igniter module. Cost was around $70 for parts. Cheaper than a new cooktop.

Parts Used:

Paul from UPLAND, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

Parts Used:

Top Electrode Mounting Clip

Dana from LEEDS, AL
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Sparking at 2 different burners all by themselves

Replaced Spark Module and adjusted igniters

Parts Used:

paul from las vegas, NV
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

very easy

there were no grate pads so it was easy to add them.

Parts Used:

ROBERT from CYPRESS, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

gas burners not heating evenly

remove old burner, put new in place

Parts Used:

Small Burner - 5K

Burner Head - Large - 12K

Burner Head - Medium - 9500

Juanita from GAINESVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The Grate foot is to big for the hole.

I had to drill the hole to a larger size to enable the foot to fit.

Parts Used:

Harold from Broadalbin, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.

Nothing technical.

Parts Used:

Chelagh from Fredericksburg, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Grate foot bdroke off allowing grate to scratch cooktop

Used scribe to remove grate foot plug still in grate inserted new foot.

Parts Used:

John from Tijeras, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

To Replace Gas And Burner Parts In Section 4

Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete

Parts Used:

Top Burner Spark Electrode

John from Long Beach, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Leaking from front door

First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.

Parts Used:

Gene from Simi Valley, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

1 of 9 people found this instruction helpful.

Was this instruction helpful to you?

The spark module would constantly spark

I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.

Parts Used:

Douglas from Knoxville, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

One Burner would not light when using the corresponding knob..

Good way to tell/verify what your problem is. On my GE Cooktop, moving any of the knobs to light cause a spark for all igniters. One of our knobs would not cause a spark. - Remove gas grills and covers. - Remove screws - Pull igniters up (be gentle to not crack them - Pull wire out from igniter - lift cover of cooktop - pull harness off each know and disconnect two wires - put new harness on and connect and backfill. Pretty easy overall.

Parts Used:

Vincent from Leesburg, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Constant Sparking on front burners

Easy to replace - caution to make sure spark igniter switch is aligned and secured in correct position on the gas valve. The switch should cover both mounting screws on the gas valve when properly installed/aligned

Parts Used:

Ken from Mandeville, LA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Ingiter Switch shorted; needed to be replaced

TURN OFF GAS and unplug stove. Removed burners (used screw driver to remove screws) and spark ignitors (used pliers). Lifted top cover of stove and unpluged the harness assembly(pulls out easily). Inserted new harness and replaced cover. Replaced burner parts included new spark ignitor. Plug power cord and turn on gas.

Parts Used: