GE/GE_Thumb/00122344i02.gif
See part 323 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Spark Igniter Switch and Harness Assembly

★★★★★
★★★★★
1 Review
$41.82   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS953094
Manufacturer Part Number WB18T10339
Manufactured by GE
Product Description

Spark Igniter Switch and Harness Assembly Specifications

This part is the spark igniter switch and harness assembly for your gas range. This harness assembly has 4 igniter switches already wired into it. It includes the igniter switches and the complete wire harness for all the surface burners. The igniter switches ignite the fuel for your cooktop. If one of the igniter switches has gone bad, you will need to replace the entire assembly. Be sure to disconnect your range from the fuel source before you begin this repair. This is an OEM part sourced directly from the manufacturer.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Will Not Start | Gas igniter glows | but will not light
This part works with the following products:
Cooktop, Range.
This part works with the following products:
General Electric, Kenmore.
Part# WB18T10339 replaces these:
AP3783914, 1063631, WB18T10219
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

9 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Doug
    January 1, 2018
    I have a problem where back right burner (small one) does not spark when knob is turned. I've already replaced the spark module. No change. I have a GE jgsp23wey7ww. Is this compatible with my stove? When i looked if this part was compatible, i did not see my model number.
    For model number JGSP23WEY7WW
    Hi Doug, Thank you for the question. The Spark igniter Switch and Harness for the model number provided is PartSelect Number PS953100. Good luck with the repair!

    5 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Mike
    October 15, 2017
    This part, does it control the clicking noise you hear when you turn the knob to ignite burner? I have a clicking noise that starts when I plug the stove in and will not stop till I unplug the stove. I shut the stove for a couple days after a full clean and plugged it in and no clicking, once the knob was turned the clicking started and would not stop till I unplugged stove.
    For model number JGP329DET2BB
    Hi Mike, Thank you for the question. Yes the Spark Igniter Switch and Harness Assembly controls the clicking you hear. If there is a constant click the harness will need to be replaced. Hope this helps!

    4 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Mary
    November 10, 2017
    Where do the wire go to burner
    For model number Sf216lxsqo
    Hi Mary, Thank you for your inquiry. There is some information from our website that you may find helpful. It was from a customer comment, "Do not remove the gas line. Take off the burner racks and burner covers Gently extract/remove the ignitors from each burner. You may have to use pliers, but be careful. They are ceramic. Once you pull out the ignitors, you can remove the ignitors from their wires using plyers, you may have to twist them a little. To take off the top - use Star screw drivers to remove the burners Remove all the burners. The star screws, and the burners are the only thing holding the top on. Take off the steel top. That exposes the ignitor switch assembly. Make sure you follow the positioning diagram that comes with the new part. Thats it really. I removed the gas, because I thought I had to, but you don't need to. You can do the whole job in 30 minutes if you are careful." I hope this helps. Thank you and have a great day!

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Jon
    February 13, 2020
    The replacement harness switch has the color of the wires switched compared to the original, has the black wire going to the power cord and the yellow going to the spark module. The replacement has the color of the wire reversed - should i flip the wires to allow for the same color connections or follow the same path as the original and therefore have the blac wire going to the spark module?
    For model number Wb18t10339
    Hello Jon, Thank you for the question. You should follow the same path as the original. we hope this helps.

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Scott
    February 19, 2020
    All if the surface igniters continually fire. I have replaced all igniters and ignition module already with no luck. Is this what i'm looking for and will it fit my range?
    For model number JGB700EE74ES
    Hello and thank you for writing. It certainly sounds like a short or loose contact somewhere in the wiring. There is no assembly for your unit, but the following harnesses are available: Switch Harness PS12702961 Ground harness PS11773746 Electrodes harness PS11762469 You should check the wiring for possible burn marks . We hope this helps. Please contact us anytime if you require further assistance.

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Jim
    December 20, 2018
    Do you have the ignitor wiring harness for the above cook top,if how much is it and what is the part #. Thanks jim
    For model number JGP336BEV2BB
    Hi Jim, thank you for your question. Unfortunately that part has been discontinued by the manufacturer and the manufacturer has not provided an authorized substitute.The only other thing that I could think of would be to contact your manufacturer and see if they have another part from a different model that will work with yours. If they do have another part that will work, get the part number so that you can search it on our website to see the cost of the part. I hope that helps. Good luck with your repair.

    Was this helpful?
    Thank you for voting!
    Bharat
    February 7, 2020
    I have one burner not sparking and igniting. All other burners ignite. Also I see one burner always sparking even though I am trying to fire another one but whichever burner I want to light up, it starts except the one with issue. Which part I would need to change.
    For model number JGP328BEK1BB
    Hello Bharat, Thank you for the question. This could be an issue with the Spark electrode for that burner. The Electrode is sold as part of the burner tube assembly. We hope this helps.

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Rick
    February 12, 2020
    My stove top clicks but does not ignite, i have to use a marc to get it to light , is the harness what i need
    For model number GE JGP933SEK1SS Gas Cook Top
    Hello and thank you for writing. Whether it's grease buildup or food crumbs, one of the most common causes for a gas burner that has trouble igniting is debris blocking gas flow to the igniter. The fix: Begin by removing the grate covering the troubled burner. ... Reinstall the burner, cover and the grill, and try igniting the burner once more. If this does not fix this problem then your ignitor itself PS11736298 might be faulty, you should check the part(s) for signs of damage or test with a multimeter, and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Douglas
    February 19, 2020
    When turning on the burners. The spark goes off on rf and gas comes out. If i turn on another burner. Gas comes out of that burner but the igniter on the rf sparks. Any ideas?
    For model number JGP933BEC238
    Hello Douglas, thank you for your question. That sounds like an issue with the spark module, which is part number PS952864. We would recommend replacing the module, and if that doesn't fix the issue the spark switch harness should be replaced. I hope this helps.

    Was this helpful?
    Thank you for voting!
    Related Parts:
      Customer Repair Stories
       Average Repair Rating: 3.3 / 5.0, 8 reviews. What's this?
        Sort by:
        Sorry, we couldn't find any existing installation instruction that matched.
        Constant Clicking from the igniters
        I first removed the top of the cooktop, which was 12 screws with a special star shape to them. Then had to pull the igniters out with some pliers (they have a really tight fit). Then remove the harness. Then I replaced the harness. After assembling, I replaced one of the ceramic igniters due to it being covered in baked on grease. Worked perfectly after that. I thank PartSelect for having super fast delivery. I ordered my parts on a Monday, they were at my doorstep the very next day, I was like WOW. And I chose regular shipping. Thank you very much for your service and your salespeople were VERY helpful, even after 3 order changes.
        • Russell from Reedley, CA
        • Difficulty Level:
          Easy
        • Total Repair Time:
          15 - 30 mins
        • Tools:
          Pliers, Screw drivers
        • Parts Used:
          WB18T10339, WB13K10014
        45 of 57 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Spark would not turn off.
        Removed the burers using a torx wrench disconnected the spark wire then replaced the spark generator and the wire harness to the gas valves.
        Installation went smooth and easy.
        replaced the spark wire and re-assembled the burnners. very easy repair. replaced the sark generator though it didn't need it because I didn't want to un-assessemble the unit again at a later date.
        • Frank from Steilacoom, WA
        • Difficulty Level:
          Easy
        • Total Repair Time:
          1- 2 hours
        • Tools:
          Nutdriver, Pliers
        • Parts Used:
          WB18T10339, WB13T10046
        21 of 26 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        No click or ignition after turning on burner - had to replace Ignitor Switch assembly
        Do not remove the gas line.

        Take off the burner racks and burner covers

        Gently extract/remove the ignitors from each burner. You may have to use pliers, but be careful. They are ceramic.

        Once you pull out the ignitors, you can remove the ignitors from their wires using plyers, you may have to twist them a little.

        To take off the top - use Star screw drivers to remove the burners

        Remove all the burners.

        The star screws, and the burners are the only thing holding the top on.

        Take off the steel top.

        That exposes the ignitor switch assembly.

        Make sure you follow the positioning diagram that comes with the new part.

        Thats it really.

        I removed the gas, because I thought I had to, but you don't need to. You can do the whole job in 30 minutes if you are careful.

        Hope it helps.

        You'll have to
        • Ken from Stony Brook, NY
        • Difficulty Level:
          A Bit Difficult
        • Total Repair Time:
          1- 2 hours
        • Tools:
          Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
        • Parts Used:
          WB18T10339
        20 of 23 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Shorted out the Spark igniter blew on gas stovetop and I had to repace it
        In order to replace the spark igniter switch and harness, order the appropriate model replacement part for your GE gas model. Turn of the circuit breaker if it is not already in the locked off position. Remove grates, gas covers, knobs and all from the cooktop surface. Unscrew all the screws with a clover tipped screw driver. Pull up and out on the 4 porcelain flints at each burner. Lift top up. You will see the part that needs to be replaced to your far right. Unplug it and remove it. Replace and connect the replacement. Reverse the process on opening the stovetop until everything is back in place as before. Flip your circuit breaker back on. Done.
        • Daryl from Tampa, FL
        • Difficulty Level:
          Easy
        • Total Repair Time:
          15 - 30 mins
        • Parts Used:
          WB18T10339
        8 of 11 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Gas coke top wouldn't lite
        First step is to turn off the electrical then disassemble the cook top. It is secured to pan by each of the burner mechanisms. Disconnect the spark wire from each porcelain drip pan. Separate the glass top from the pan. If it's stuck gently slide a putty knife int between the two to separate and carefully set the glass top aside. The spark module was a bit challenging in that the colors of the wires didn't match so if you aren't comfortable with electrical work I would get help. The module didn't fit the bracket so,I had to drill new holes and use self tapping screws to mount it. The other part part I intended to change was the spark igniter switch. Unfortunately the wiring was incompatible so I had to return that part. This top was sold by Kenmore but made by GE and is over 10 years old so I suspect an engineering change obsoleted my part. Overall the job wasn't that bad if you are reasonably mechanical..
        • James from ABINGDON, VA
        • Difficulty Level:
          A Bit Difficult
        • Total Repair Time:
          30 - 60 mins
        • Tools:
          Nutdriver, Screw drivers
        • Parts Used:
          WB18T10339, WB13T10046
        3 of 4 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Igniter constantly ticking ...
        Unplug!!
        Pull knobs
        Pull burner centers
        Unscrew the nut at the center of each burner
        Tilt cover up revealing under burner controls
        Remove old harness
        Install new harness
        Reassemble in reverse order
        Plug in NO ticking
        • steve from BEAVERCREEK, OH
        • Difficulty Level:
          Easy
        • Total Repair Time:
          15 - 30 mins
        • Tools:
          Pliers, Socket set
        • Parts Used:
          WB18T10339
        2 of 2 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Igniters would not turn off
        Replaced starter switch harness as well as igniter module. Cost was around $70 for parts. Cheaper than a new cooktop.
        • Paul from UPLAND, CA
        • Difficulty Level:
          Really Easy
        • Total Repair Time:
          15 - 30 mins
        • Tools:
          Pliers, Screw drivers
        • Parts Used:
          WB18T10339, WB13T10046
        1 person found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Igniters would not stop clicking
        Removed burners and screws. Then removed handles and stainless top. to access the spark igniter switch and assembly. The removed wires from the spark igniter module and each burner handle and replaced with new repair harness. put stove back together with new burner gaskets. Problem solved
        1 of 2 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
          Customer Reviews
          Average Rating:
          ★★★★★
          ★★★★★
          1 Review
          5.0
          Filter By Rating:
          • 5 Stars
            1
          • 4 Stars
            0
          • 3 Stars
            0
          • 2 Stars
            0
          • 1 Star
            0
            Sort by:
            Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
              Model Cross Reference
              This part works with the following models:
              PartSelect Number: PS953094
              Manufacturer Part Number: WB18T10339
              Brand
              Model Number
              Description
              Kenmore
              91132212101
              Cooktop
              Kenmore
              91132212102
              Cooktop
              Kenmore
              91132214101
              Cooktop
              Kenmore
              91132214102
              Cooktop
              Kenmore
              91132219101
              Cooktop
              Kenmore
              91132219102
              Cooktop
              Kenmore
              91133202101
              Cooktop
              Kenmore
              91133202102
              Cooktop
              Kenmore
              91133203101
              Cooktop
              Kenmore
              91133203102
              Cooktop
              Kenmore
              91133204101
              Cooktop
              Kenmore
              91133204102
              Cooktop
              Kenmore
              91133209101
              Cooktop
              Kenmore
              91133209102
              Cooktop
              General Electric
              JGP328BEC2BB
              Cooktop - Gas
              General Electric
              JGP328BEJ1BB
              Cooktop - Gas
              General Electric
              JGP328BEK1BB
              Cooktop - Gas
              General Electric
              JGP328BEK2BB
              Cooktop - Gas
              General Electric
              JGP328BEKB
              Range - GE Range/Stove/Oven Model JGP328BEKB Parts
              General Electric
              JGP328CEC2CC
              Cooktop - Gas
              General Electric
              JGP328CEJ1CC
              Cooktop - Gas
              General Electric
              JGP328CEK1CC
              Cooktop - Gas
              General Electric
              JGP328CEK2CC
              Cooktop - Gas
              General Electric
              JGP328CEKC
              Range - GE Range/Stove/Oven Model JGP328CEKC Parts
              General Electric
              JGP328SEJ1SS
              Cooktop - Gas
              General Electric
              JGP328SEK1SS
              Cooktop - Gas
              General Electric
              JGP328SEK2SS
              Cooktop - Gas
              General Electric
              JGP328SEKS
              Range - GE Range/Stove/Oven Model JGP328SEKS Parts
              General Electric
              JGP328WEC2WW
              Cooktop - Gas
              General Electric
              JGP328WEJ1WW
              Cooktop - Gas

              Get in touch, we're here to help!

              Open until 10PM EST

              Contact Customer Service