JB710WF2WW General Electric Range - Instructions

unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .

I removed the screws from the underside of the stovetop, lifted up the top, propped it up to keep it from falling (using a large book), and removed the old burner by unscrewing it from the top and removing the wire connections. I then screwed the new burner into the top, and attached the wires back to the burner, dropped the top down (gently and carefully, of course), and screwed the top back down to the rest of the stove. It was fairly quick and painless. Although, putting the stove back into his position was not easy, but that was no fault of the stove!!

couldn't get exact fit--out of production. mounting bracket at back of range for new element too small. took bracket off old element. cut down bracket on new element with tin snips, drilled holes thru it and old bracket and screwed together. at this point the new element was to long & touched oven door. removed spacers that came with new element (used old support to attached to roof of oven) and pried elements apart (which made element wider & shorter). working good.

Would have helped it I knew the push on terminals of the bake element were visible and accessible to slide the terminals on from the back side of the stove in the beginning. There is not enough slack in the the terminal wires to connect them from the oven side, so you will have to open the back panel to retrieve a wire anyway. SO, CONNECT THE BAKE ELEMENT TO THE OVEN WALL FIRST ! Then, open the back panel of the stove and simply slide the terminals on the exposed slide terminals of the bake element.

Pulled the stove out from between the cabinets, used a blade screwdriver to pop the oven door retainers down and lifted the oven door out, removed the racks. used a 1/4'' nut driver to remove the 5 screws holding the broiler in place. From the time I unplugged the stove from the outlet until I plugged the stove back in was 15 min. I would suggest wearing gloves because the metal frame around the burner element has sharp edges.

Removed door from range(see manual for instructions). Set door face down on protective cloth material .Remove two top screwws, 3 bottom screws and lift back of door off. Remove two screws on each side of door bottom channel and remove channel. Put in new trim on bottom of glass window and put screws back in. Set back of door on top of front cover and screw two top screws and 3 bottom screws back in. Set door back into range. Lock clips on both hinges.

On a 18 year old electric GE range: amazing not the exact handle but it does fit perfectly and looks great. If your somewhat handy this is very easy and can be completed in less than a half hour. Save the screws from the old handle, they can be used again.

Lots of jiggling until I found the screws to remove. After finally getting the top off the base there was the Instructions on a pamphlet taped to the bottom. The key tho get the top off is to remove the face and remove the proper screws( they are identifiable)unplug the electric plug 2 screws on the back sides and poof it is free!

The part was exactly what we needed. However, we didn't find the video online to show how to replace the part until we were almost finished. (https://www.youtube.com/watch?v=ovwcJhfWHXQ) If we had found the video, it would have saved us a lot of time because we undid more of the door than we needed to. Also, the video tells you exactly what size tools to use. However, taking the door more apart allowed us to clean more of the inside of the door. So, watch the video before you start, and also, be prepared to spend time cleaning the insides of the door. Also, when we put the door back together, we accidentally turned the front glass panel of the door upside down and it wasn't noticeable until we had put the door back on the oven. So, we had to take it apart again to fix it. All said, we're very happy with the new part. Thank you PartSelect!

replaced lights in refrigirator and freezer

The only hard thing was contorting my old beat up body and joints long enuff to reconnect the 2 wires and oven heat sensor and put in 6 screws with a 1/4" nut driver. I did remover the oven door and that made it much easier for me.

Remove two screws hold cook top down: prop it open with piece of wood. (TURN OFF POWER TO RANGE FIRST!). Carefully make diagram of where wires go: remove and replace.. piece of cake!

Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

I too made the mistake of cleaning the oven with the shelves in place. It doesn't really harm them...but they turn a tarnished brown color...they look dirty. These replacement shelves were a perfect match. Pricing was reasonable, communication was terrific and shipping was super fast. Happy camper here :-)

Ordered the bake element part from partselect.com. When the part arrived I removed the 2 6mm screws from the element, I used two clips to hold the wires in place so that they didn't receed back into the stove. I installed the bake element, installed the two scews ans was done. It took all of 10minutes.

Lily in Florida