JB710WF2WW General Electric Range - Instructions

Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...

Unplug stove first. Raised the stove top and propped up useing wooden spoon and wife assistance holding up. Pay attention to spot brackets hand to top. Removed sheet metal screws from bracket clamp holding burner in place. Removed one extension bracket from old burner and transfeered to new burner. Removeing one bracket clamp allows the other one to act like a hinge and make for easy removal and replacement. Back of burner had corresponding numbers which made it easy to replace brackets in same place as old. I carefully take one electrical wire at a time from old burner and transfeered to the new burner. Replaced burner same way it came off.

unplug stove first...take back of stove off to get to burner switch remove wires colors coded.. get new switch put wires on the same way.plug stove in test burner...very simple to replace.and save $$$$$$$$

When we moved into our new home I discovered that the oven that came with the home did not have any racks in it. I ordered these racks because they said they were compatible with Hotpoint ovens. However, when the racks arrived they were just a tad too wide to easily slide in the oven. With a bit of force my husband was able to shove the racks in. Luckily I don't cook enough to care if they are moved again because I don't think they'll come out easily.

TURNED OFF CIRCUIT BREAKER FIRST. Pulled Stove from wall, Removed 5 screws to remove back plate. Unplugged 2 spade electrical connections. Unpluged temp. sensor plug. Opened oven door and removed 2 screws holding element to top of oven. removed screw holding temp probe to element. Installed the elment in the reverse order starting with the temp probe. when finished with install, I tested the unit before covering the back. I used a oven temp tester to make sure that when the element went out that the temp probe was not damaged. Everything checked out fine and I finished installing the back cover and putting stove in place. Cleaned up area and JOB DONE.

Used a pliers to remove old bake element (2 nuts that none of our socket set would fit). Removed the back panel with screwdriver. Unattached bake element from wires. Then removed old element and put new element in, pulled new element wires through back and reattached to range. Screwed back in the oven with the pliers. Closed up the back panel with the screws.

First I shut off power to the unit. Then I removed the oven shelves. Next, I removed the two screws that hold the element in place using a socket ratchet. Then I carefully pulled the element out a few inches. I had some clothes pins with me because I read how some people had problems with the wire leads slipping back into the unit insulation. When the terminals and wire leads were exposed, I clamped the clothes pins on the wires between the leads and the oven wall so the wires could not be pulled back into the wall. Then I disconnected the wires from the old element. Next, I connected the new element to the wires, removed the clothes pins and gently nudge the element terminals back into the oven wall. Then I put the screws back to secure the element. Finally, I turn the power on and set the oven to 400 degrees. When I saw the element get red hot in a couple of minutes, I knew it was fixed. I've used it several times since then.

I changed out the sensor and still same problem. Change out Thermosat and still same problem.
I call the help number and emailed the help but I got nothing but have to many calls because of the virus situation.
Still need help.
I’m an electrician and I don’t want to call a service technician and pay that big bill.
Can anyone there help me out, if so please call.
Ike Stanton
678-525-6644

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

I unplugged the stove then took the oven racks out. Then I took a nutdriver and took out the 2 screws that held the Bake Element in place. Pulled the 2 prong's out of the oven and removed the wires from the tips. They pulled right off.
Took out the new Bake Element and reversed the process. Attached the 2 wires put the 2 prong's back into the holes and screwed the 2 holding screws back in. Plugged the Stove back in and turned her on. Doing it myself saved me $150.00.

Turn off power to oven,remove two screws holding element in place,pull element forward approx. 1" and unplug wires,remove element. Install new element in reverse order of above.

First, UNPLUG OVEN. Then, remove oven door and place stove on work bench! JUST KIDDING!! Honestly, the repair would be easy if that were possible.The hardest part is kneeling, standing, hunching over, twisting your body holding flashlight in your mouth, etc...THEN, trying to re-attach wires screws etc. The repair is straight forward. unscrew all screws holding element in, pull element out about 6 inches, detach wires, and re-attach. Simple right? Maybe if you're 1 foot 2 inches tall or have 6 foot arms

Removed the old element with a nut diver and put the new one in. Very simple instalation.

Amazingly the part arrived in just two days...

My T-Bone steaks are cooked just the way I like them again.

MikeS, Birdsboro, PA

Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven temperature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!