JB655YK6FS General Electric Range - Instructions

Initially replaced the switch on the range--a simple job--pull the wires one by one and place them on the new switch. This did not resolve the problem, which meant that it was the burner, not the switch. I left the new switch in place and ordered a new burner. This, too, was simple, but involved creating a detailed drawing of the switch connectors rather than photos, which, because of the crossing of similarly colored wires, might have been confusing. The only hitch was that the burner is attached to the top by indented clips that fit into pegs at numbered locations on the burner. The clips were very difficult to open and situate, but once done (and this step was the only one where a second person was required) the top was closed and screwed back in place (two screws) and it worked perfectly.

Red Light Off

Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.

Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.

Safety first * Unplugged 220 VAC from outlet. Removed shield cover screws with 1/4" hex nut driver (5 screws). Removed all 6 silver screws from terminal block with 1/4" nut driver, freeing all wires. Removed the green ground screw and ground bracket from center terminal. Cut away (using the drill) melted original terminal block plastic to access the 2 black 1/4" nuts holding original terminal block onto appliance. Discarded the original damaged terminal block. Attached the new terminal block, aligning the mounting holes and the terminal block the same way the original terminal block was lined up and re-used the black 1/4" nuts (original used because the replacement package did not include new black screws). I bought a new appliance cord, since the original cord overheated. Reattached all wires using the 6 new silver screws. Start with the middle terminal by attaching the appliance wires and the ground bracket. The ground must be attached to the bracket and the bracket bridges between the terminal block and the range body. Reattached shield cover. Plugged in appliance. Note: it doesn't matter which outside wire attaches to the outside terminals (both are hot), but the middle wire (neutral) must attach to the middle terminal. However, the ring terminal should be flush on the terminal block so you don't bend the ring.

Well I did it all wrong from the get go. I did finally do a search on how to replace it and then it was quite easy. Learn from me, watch video and save yourself tons of hassle.

I looked everywhere for this part before I came upo9n this site. I found the part from their very well done website. Even had a picture so you could compare to what you have. It was an easy repair. I had been quoted over $200 to repair by a local repair place. Instead it was around $25 and 15 minutes to repair. This is the right site for any part you may need. I have a magnetic card they sent so in the future, if I need anything (and I will !) I can go right to the right place . Thanks also for a very prompt delivery.

Watched repair videos on YouTube to prepare. The repair was very easy.

After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove the swith assembley from the front panel.

I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)

Being a front burner, I used a 24 in piece of wood to hold up range top. After removing to screws holding top. Made note of numbers on old burner and wire locations. Took off wires and three spring clips. Then replaced with new in numbered locations , wires next

After the volunteer experts at partselect told us which part we would likely need, once it came we found a diagram of the back of the stove and a video showing us how to do it. We turned off the circuit breaker, unscrewed the top of the back and replaced the part.

Replace Element Radiant 9 inch dual is very easy.

I am not the handiest person in the world, and this repair was easy even for me. If you suspect that the temperature sensor is the problem, do yourself a favor and buy this inexpensive replacement part and install it yourself prior to calling a professional who will charge a service fee just for checking it out. Pull your oven out from the wall so you can access the back. Unscrew the small nuts on the back to remove the sheet metal cover. Find the wire that goes to the sensor and unplug the plastic coupling. In the oven, unscrew the one nut that secures the sensor to the back wall of the oven. Pull the broken sensor out and replace it with the new sensor. Feed the wire through to the back and plug the new sensor into the same wire that was just disconnected. Reinstall all of the nuts. Do a "test cook" on some frozen food to ensure that the temperature seems correct (i.e., does it cook as expected in the recommended amount of time). The actual repair takes less than five minutes. I put "30-60 minutes" to account for unplugging the oven, pulling it out, removing the screws, replacing the screws, pushing it back in, and testing the temperature.

This temperature sensor is very easy to replace. There are two screws inside the oven in the top middle of the back of the oven. Take these off. on the back of the stove there is a metal plate with 5 screws I believe. Take these off with a nut driver. Then you will see a white connector coming from the spot where you took the other screws off. Take the white connector apart and pull out the temperature sensor from the inside of the oven. Then put the new one in.

Replaced