JB620DF4BB General Electric Range - Instructions

Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

Ordered the bake element part from partselect.com. When the part arrived I removed the 2 6mm screws from the element, I used two clips to hold the wires in place so that they didn't receed back into the stove. I installed the bake element, installed the two scews ans was done. It took all of 10minutes.

Lily in Florida

First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.

I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.

The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.

Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.

Followed directions given by previous customers problems which we found on the internet.

This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.

We ordered the part from PartSelect and received it the next day. Didn't even have to move the range out from the wall. Just unscrewed the two screws on the back wall of the stove that hold the bake element in place with a socket wrench, then pulled the old bake element and wires out about 2-3 inches so we could disconnect the old bake unit. The element was kind of hard to pull out, but after you pull it from the wires, just plug in the new bake unit, push the wires back in and put the screws back in. Oven was up and working again!

Becuase of the fire we had used a chemical based fire extinguisher, which made a real mess in the whole main floor of the house. I removed the oven from the house and used a leaf blower to get rid of all the white chemical powder (like a baking soda of sorts). Once that issue was done, I removed the part in less than 5 minutes. Two screws to remove it and then unpluged the two wire clips from the back of the stove under the shield which also had 6 screws to remove. It took only 3 days to have a new one delivered and I installed it in less than 5 minutes. The oven works fine now. It took much longer to clean the house than fix the oven.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Ordered the part, it arrived and 5 minutes later it a complete installation

1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.

replaced Plastic Guides

Watched video on you tube. Removing/reinstalling all of the screws/bolts took longer than the actual repair.. Took 23 minutes total from turning power off, repairing and turning back on. Super easy!

pulled range out,unplugged it,thenI removed the two screws that hold the element in place.take back cover off, then pulled the element out about 3 inches and disconnected the two wires.put new element in,put wires and screws back in place,checked to see if worked,did not work,check and reset breaker,it works put cover back on,push range in palce and done.

One wire at at time then used my razor blade to get front off stuck right back on