JB500G2D4 General Electric Range - Instructions

First I read the already posted repair stories to give me confidence I could perform the repair.
Followed their steps -
Removed the two screws holding the plate to the oven.
Pulled out the element.
Removed the two screws holding the wires to the element.
Installed the new element by attaching the two screws (which were supplied) to the element.
Reinstalled the plate to the oven.
Tested it and it worked perfectly saving a costly service call.

It was so easy. Just removed the cover and then unscrewed the wires (keep track of which wires go to which side). Do teh reverse to reinstall

Repair was as easy as one, two three. Turned off the power and removed the two screws holding the element in place. Then pulled the element out approx. 3 inches and removed the two screws connecting the wires to the element.

From there I reversed the process and the repair was complete in less then 5 minutes, and I am not a electrician.

This was extremely easy to replace. When I told my mom I would replace it for her, she thought I was crazy. When she saw how easy it was, she finally understood. I had to remove the two screws holding the element in place. I pulled it out about 3 inches and unscrewed one screw for one wire. I didn't want to lose the wire, so I immediately connected the wire to the new element. I disconnected the second wire and attached it to the new bake element. Then attached the two screws putting the plate back up, securing the element. So easy! Just unscrewing and replacing 4 screws and I was done!! Took less than 10 minutes. I didn't have any real tools available, so I used a small adjustable wrench and it worked fine. The best part was it was so easy we were able to have a working oven in time for Thanksgiving!

First I removed the one screw that hold the terminal block in place. I then pulled the terminal block out about 3 inches and unscrewed the two screws and disconnected the two wires. Then I got the new terminal block and re-attached the two wires with the two screws. Then I screwed the terminal blocked with the one screw and then I inserted the 8" Surface Element and I turned it on and it heated up very quickly. It works better than it has in many years.

Pulled out the bottom drawer of the stove and discovered the plug. So the plug was pulled from the wall socket.

Before this I had sprayed the screws with WD-40 and let it sit for 2 days.

Screws came out easily. Pulled out the old element and removed screws. Screwed on new element on both sides. Put in place and put old screws back.

Plugged stove back in. Turned on stove. Element came right on.

super easy - unpluged stove - unscrewed old element w/nutdriver from back of stove. unwired element - discarded. wired new element (2 wires). secured new element to back of stove. pluged stove back in. works great. Ordered part on Sunday, recieved it on Tuesday- VERY NICE SERVICE

The interesting part of this story was troubleshooting the problem. Was it the element or the control? Turns out the element was making poor contact, generating excess heat ,which corroded the element contact generating even more heat, and so on and so on until the termional block eventually broke. The repair itself was simple once I separated the element from the terminal block. After that I removed the terminal block, one screw, removed the connecting wires, two screws, reversed the procedure to install the the new terminal boplck and element. Before the whole process began I made sure to turn the breaker to OFF.

I turned off the electricity, unscrewed the old one and disconnected the electric wires, then put the new one in just like the old one. It was very easy and now it works great.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...I copy and pasted this from their example - it really is that easy - this is a simple repair.

Just like your example said/turn the power off to the oven/remove the screws that hold the element in place and then I pulled th element out a little ways and disconnected the wires/reconnecting took a little longer only because it was hard to see/but I connected the two wires and put the screws back in and it worked. Saved me a lot of money/my husband wanted to get a new double oven

It was so simple, I turned off the breker to the oven, unscrewed two screws holding in the element, pulled out until the wire connetion was exposed. I unscrewed those two screws, then placed the replacement part, put the two screws on, pushed back the wiring and insulation.Final step was screwing two screws to hold the unit to the oven back. So simple! The part was ordered regular mail and still was here in 2 days. Will recommend to friends for sure!

Very easy and simple/ After making sure power supply was off, removed socket screws in back plate of element, slid old element out, attached new element and replaced/tightened socket screws on plate and new element. Power on, oven on .. heated quickly and nicely. Used oven several times since ... no problems.

Unscrewed the element from the oven,disconnected the two screws for the electrical and reverse the procedure to install new element. Took all of about 10 minutes.

Snapped in place (4)