JB350DF2CC General Electric Range - Instructions

Replaced

First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.

I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.

The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.

Ordered the bake element part from partselect.com. When the part arrived I removed the 2 6mm screws from the element, I used two clips to hold the wires in place so that they didn't receed back into the stove. I installed the bake element, installed the two scews ans was done. It took all of 10minutes.

Lily in Florida

Removed the old burner bowls, replacing them with the new ones.

I didn't know anything about this repair, other than I was replacing a part, so it never occurred to me that I needed to make sure there was no power to the oven. When I pulled the element out, there was a large spark. I flipped the breaker off, then finished the R&R.

Make sure you turn power off at the breaker, then replace the element.

Tim

Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.

I just removed the drawer and installed the rear supports as instructed on paper included with the part.

Becuase of the fire we had used a chemical based fire extinguisher, which made a real mess in the whole main floor of the house. I removed the oven from the house and used a leaf blower to get rid of all the white chemical powder (like a baking soda of sorts). Once that issue was done, I removed the part in less than 5 minutes. Two screws to remove it and then unpluged the two wire clips from the back of the stove under the shield which also had 6 screws to remove. It took only 3 days to have a new one delivered and I installed it in less than 5 minutes. The oven works fine now. It took much longer to clean the house than fix the oven.

This was a very simple procedure. I removed the 2 screws in the oven itself (holding the element in place), then pushed the element through the back of the oven so the wires were exposed, then slipped off the wires, the male end from the female end, I then removed the entire element. I put the new element in the over, re-attached the wires, put the screws back in place, replaced the cover, and the oven was as good as new.

We ordered the part from PartSelect and received it the next day. Didn't even have to move the range out from the wall. Just unscrewed the two screws on the back wall of the stove that hold the bake element in place with a socket wrench, then pulled the old bake element and wires out about 2-3 inches so we could disconnect the old bake unit. The element was kind of hard to pull out, but after you pull it from the wires, just plug in the new bake unit, push the wires back in and put the screws back in. Oven was up and working again!

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

1.Disconnect the power cord. 2.Remove two screws pull the element out. 3.Disconnect the wires attach to element. 4. Install the new element connecting the wires. 5. Align element with holes and tighten screws. 6. Plug in power cord and begin to cook.

Removed the rear panel from the Range using the nut driver. pulled the terminal wires off the back of the heating element. Double checked if there was continuity across the heating element terminals before removing the element. If there is none, its bad. remove the two screws inside the oven holding the element in place. Once free, lift the front of the element to about 30 degrees and pull towards you. Insert the new element in the reverse manner then secure it using the two screws. Push the terminal wires onto the terminals on the back of the element and reinstall the rear panel.

My son did it by using pliers. He took out the screws that held the element in and pulled it out and used the pliers to pull the wires out of the old one and snapped the new one in . put it back together. about 5 minutes.

1) Make sure unit switches are turned off. 2) Lift Calrod unit up and pull it from electrical receptacle. 3) Withdraw Calrod unit from old bowl. 4) Insert Calrod unit through large hole in new bowl. 5) Push Calrod electrical connectors into receptacle under range top. 6) Seat Calrod unit on bowl rim and insert the assembled Calrod unit and bowl into the hole in the range top.