J303V4WH General Electric Range - Instructions

Lifted burner element to remove pressure on ring and drip bowl. Removed old parts and replaced in reverse order. This not intended to sound sexist, but my wife who is not particularily mechanically inclined performed the task on her own.

Just lifted the electric components Remove drip plans and trim rings and replaced with new drip pans and trim. Your company was incredible in there delivery of the parts..One day. You made my husbands very happy.

the replacement items fit really good. It was a matter of remove and replace,

Removed the plug from wall socket.
Removed door to oven by lifting it straight up while partially open, in locked position.
Remove Baking shelves.
Removed 2 screws @ the back of element where it goes into the ovens back wall with a nut wrench and gently pull the element towards you until wires are exposed.
Using a flat blade screw driver hold on to the end of the element near the end with the screw and support it as you un screw the wire so the end of the element does not bend as you turn the screw.
After both wires are removed, remove the old element.
Install the new Element in reverse.
Very Easy!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. connected the wires to the new element. pushed the element back in place the screwed it back to the back of the stove.

Shut power off. Removed two outer screws, pulled heating element forward and removed two more screws. Ordered part and it arrived in three days. Installed in reverse order of removal. Easy fix. Cost was reasonable.

The part arrived ahead of time by mail. I removed the old coil, very simple,, I installed the new one just as easy , Turned on oven and it worked prefectly , its a very simple procedure, thank you

I first unplugged the stove as that was easier than going to turn off the breaker. I removed both oven racks for more room to work. There were two screws to removed inside the back of the oven. After pulling the element out a few inches I was able to unscrew the two screws that held the wires onto the element. I made sure to note which wire went on which side. Then did everything backwards with the replacement element.Plug the oven back in and make sure it works. This was the easiest repair I have ever had to make on any appliance! It's good to note the new element could heat much faster and hotter than the old one. I plan to check the temp when baking. The replacement one also hinged so cleaning in the future will be much easier as well.

lift eye slide in bowl and trim ring, put the eye back down,

Removed 2 screws (with 1/4" nut driver) on bracket holding heat element at back of oven. Pull element forward to expose the 2 wires connected to element, remove screws on wire corrections with flat head screw driver. Remove element from oven......Reverse the steps to install new heat element.....very easy job....except I cleaned the oven while I had the element out of the oven.

Customer service is great. Fast shipping. Great communication. I have them bookmarked from a previous order. Same good service as the first time. Thank you.

The complete repair was quick, easy, and painless. Not only did my item show up sooner than I thought the whole replacement took only 15 minutes, tops, to complete. I even had my 18 months old daughter helping too.

First and foremost I turned off the power to the oven by tripping the circuit breaker in the basement. Then verifying that the oven or stove top did not work to insure that the correct circuit breaker was tripped.

Then I removed the two mounting bolts on the support plate, that holds the element in place, from the rear wall of the oven. Then slide out the element just far enough to gain access to the wires that are attached to the element, about 3-6 inches. Carefully removed the two wires from the element with a screwdriver, noticing how flexible the ends of the element were. Removed the old element out of the oven. Placed the new element into the oven and then reattached the two wires to the new element terminals, being careful not to bend the ends of the element too much, very flexible!! Slide the element back into place and then reattached the mounting bolts. Turned all power back on to the stove and then turned the oven on and presto!, my oven is fully functional again.

First I removed the 2 mounting screws that mount the element to the back wall in the oven, then pulled the element out about 4 to 5 inches, then removed the 2 screws attaching the wires to the element, then reversed the process to instal the new element. The only tool reguired was a 1/4 inch nut driver. Did the job in about 5 Minutes. The replacement fit and works perfectly.

I was lucky to look at other repair stories because I forgot to turn off the power!!! Nothing happen to me, but it was as simple as everybody else said. Unscrew the two screws, pull out element, unscrew another two screws and put back together in reverse order. Viola, the oven was back in working order just in time for a major event the next day. Thanks everybody for their tips and partselect for fast shipping.

I turned off the breaker, removed two screws that held the element in place, pulled it out about four inches, disconnected the screws securing the wires to the element. Removed the old element, placed the new one in the oven and reversed the procedure.