GTWN5550D1WW General Electric Washer - Instructions

replaced them & working fine now....

With screwdriver, I removed screws holding old hose in place. Attached new hose and screwed into place.

Unplug the washing machine. There are electrical components that can injure or kill you. Using a screw driver inserted just below the lid of the washer in the front, there are two (2) spring clips that you push on to release. Then the front of the washer tilts down and you remove it and set aside.
On the bottom right you will see the flexible, convoluted rubber hose connecting from the pump to the washer tub. Two (2) clamps hold the hose on. Remove the two clamps, install the new hose and re-install the clamps. Re-install the front panel and push into place, allowing clips to lock into the front panel.

Took top off and replaced bolt.

I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.

The repair went just like the video! Easier than I would've hoped.

Took off the front panel of the washer which exposed electrical wires going to top lid sensor. Took out old sensor installed new. Cut wires from old sensor and spliced wires from new sensor to machines wires that went to old sensor. Replaced front of washer. Washer works fine now.

As an 89 years old ignorant about washing
machine repairs, I contacted a company to
come and install the new filter, which would have cost me $85,00, just to come, not to replace the filter, that price graduated me to become an instant washing machine mechanic;
but then, I read the extremely easy instructions
how to do the work; I just followed the instructions, and the machine now works like new!.
my order # was 22526491.
The Part # was PS3652834

I was instructed to call 1-888-895-1535
if I needed any assistance; But with instructions so clear, there was no need to call them back.

Thanks Partselect.com !!!

Here is how I did it: and why,
water filter was clogged up.
1: i unplogged the washing machine.
2: I shut off both, the hot and cold water hoses.
3: I removed the water hoses from the machine.
4: I removed three screws from back of control panel.
5: I pulled back the hose clamp between valve and flex hose to shower head.
(if after doing this, the hose will not move,
spray some WD40, and will move fast.)
6: remove two electrical connections on valve,
one on right, and one on left.
7:remove two screws that hold triple water valve to base.
8: replace valve in reverse order above step 7.
that is my friends, if an ignorant 89 years old
did it, you can do it aswell. God bless you all,
and don't forget, this was only possible through the expert assistance of PartSelect.
kindly buy all of your products from them
Call them:1-888-895-1535. Thanks, God Bless

Very easy to put a new water pump. You have to disconnect two hoses from the pump, unplug the power connection from the pump, and unscrew the two screws from the base of the pump.

Easy, even for a mildly competent amateur. Unplug, turn off water, remove three screws holding top piece. Remove plug in electrical connections and screws holding valve in place. Loosen clamp holding rubber hose to the valve. Put new part in place and reverse the process.
The only thing a little difficult was removing the hose between the valve and the washer. Although I did it by myself, it would be a lot easier if you had someone holding open the spring clamp that holds the hose in place, while a second person tugs the hose off the valve assembly.

I had to take out the front panel to access the Tub. Afterward the work wasn't hard.

The picture of how to depress the clips to remove the front was incorrect. The clips are 4" from the sides not immediately at the sides per the picture. The 4 rubber springs were only part of what was needed for the washer. The old gas dryer was still working. There are two more springs on the bottom of the tub missing not shown on diagrams, so it still sways side to side, bangs around and makes a lot of noise. After putting on the 4 rubber springs, it ran, but probably needed a new clutch also, because it wouldn't spin dry anymore. I ended up spending $2000 for new washer and dryer from Maytag, and throwing out these old machines today.

Pulled front panel of washing machine, removed hose, installed new hose, and wipped up water.Simple!!!

Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!

I pushed a small screwdriver under the top lid and pulled the front out and lifted it out or the way. The rubber hose had two clamps holding it. One you loosen with a flat screwdriver and the other one you squeeze with pliers to remove hose.Then replace hose and put front back on. It's very simple.