GSG746RFS2 Gibson Dryer - Instructions

remove top cover, remove front of dryer, unscrew two #2 screws from gas valve coil hol down bracket. replace coils. reassemble dryer.. works great.. had already replaced the thermostate and flame sensor.. didn't change anything.. the coil set did the trick..

The new motor from parts select was not correct. The new motor is a bolt on. The original motor was a press on. Had to return at a cost of 42.00 dollars. Had to buy a new dryer.

All I did was push the new part into the machine! So easy!

This was a Sears Dryer, also know as Kenmore, This dryer can be stacked or side by side. In this case it was stacked. There are no directions on how to replace this part. For this model made in 2005 the lid of the dryer is held in front by two clips. You open the lid simply by prying the two front corners up with a flat head screw driver. The front of the top lid pops right up. You may have to remove the mounts in back if you cant lift the dryer lid enough to be able to get your hands in. UNPLUG THE DRYER I got a nasty shock. There are two wires on the switch, remember how they go and where they are, that's important. Turn the switch (from the front or back) so that it pops out. Remove and replace the wires put it back in (from behind/top) and twist a 1/4 turn into place. Plug, test and simply push the cover back down onto the clips. Done.

Very easy and straight forward repair.

Unplug the dryer and move it to a location that offers some room to work.

Use flathead screw driver to pop the front side top of the dryer up then lift the top of the dryer up to expose the drum.

Use phillips head screw driver to remove the two screws from the access panel on the rear of the dryer. Reach into the access area and remove the drum belt from the tensioner assembly. It's spring loaded so watch your fingers.

Disconnect the wiring harness at the right front of the dryer.

Remove the two screws that secure the front of the dryer to the sides.

Remove the front panel of the dryer by pulling the panel forward then up and off the two tabs at the bottom.

The felt strips and glides (which are worn off if you are doing this repair) are glued to the front panel of the dryer and now need to be removed. Removing the old felt will take some time and is the most difficult part of this whole repair.

Use some goof off or similar solvent adhesive remover to ease the removal of the felt. A putty knife will likely be helpful too.

Once the felt is off, wipe off any excess solvent and make sure the area to be re-felted is clean and dry.

Apply small serpentine bead of provided adhesive to the felt strips and glue the new strips on to the dryer. There is more than enough glue in the tube provided to get the job done. After applying felt strips, let them sit for about 30 minutes before reassembling dryer. You may want to use some light duty clamps to hold the felt in place while the glue sets but that's probably not necessary since the glue sets rapidly. Follow the directions on the glue tube.

Reassemble in opposite order.

Take the opportunity to vacuum out your dryer and give it a good inspection while you have it cracked open. You just might find those socks that disappeared.

Here are some "while your at it" ideas:

Replace both upper and lower felt strips.
Vacuum out entire dryer cabinet and the foam seal on the air box.
Replace drive belt.
Replace light bulb.
Replace bearing ball on rear of drum or apply some lubricant to the bearing.

I'm not saying do all these things, I'm just suggesting these items as things to consider based on the age and usage of your dryer.

This is an easy one person repair that requires no experience or special tools. Don't pay the repair man. Do it yourself.

I basically followed the video instructions on your website. Pretty simple but ran into an issue pre-threading the 3 self taping screws into the spindle bearing. The screws provided were blunt on the end and did not tap easily at all. I used the existing screws that were much more "sharp" and worked much better. Also, the new screws were Philips drive and due to the amount of torque trying to self tap nearly stripped them out. The old sharper screws were square drive which had a better bite. So basically, I used the old screws to self tap and then used the new screws for the final installation.
It took a long time to clean all the lint out from the inside of the dryer. The motor was completely embedded with lint and animal hair. You may want to suggest that a good cleaning may be needed so bring a shop vac...and also something to carefully pick the lint balls out from around the motor armature and bearing area. Overall the video instructions were really a big help!

Almost exactly as per the videos available on the PartSelect web site. The only additional information that would help is that the vent on the back of the unit can be removed to allow for access to the belt spring pulley. This avoids having to reach around from the front of the unit and feel your way to remove and re-install the belt.

I remove the old lint filter and just put the new one in.

I bought part PS419092 (Rotary Knob) for my Firgidaire FDGB23RGS2 Dryer.

This knob I bought (PS419092) is much cheaper than the parts recommeneded for Frigidaire dryers ( knobs: PS417309 and PS416982 ). It is $6 instead of $18.

The only difference is that it (PS419092) is white instead of cream/off-white.

Putting the knob on was super easy and I'm glad I saved money by buying the less expensive part.

Replace rear bearing, found Exhust tube seal broken. Went ahead and replaced Drum belt & Idler arm assembly. Works like New !

Unplugged the drier, a couple of screws, remove the wires (take a picture of the wires with your cell phone to remember how they go back, twist out the thermostat. Installation is the reverse. A piece of cake.

Determined that the coil on the gas valve wasn't pulling in to ignite. Using an ohmmeter, I determined the coil was open. The coil was removed by pulling off the wire connecter and removing the two phillips screws holding the bracket over the two coils. The coil then slides out. I slid the new coil into place, replaced the bracket and two screws and reconnected the wire connector. It worked immediately. The actual repair only took 15 minutes. The bulk of the time was spent tracking down which part had failed.

Raise the top and remove the front panel assembly. One philips screw, 24mm gas line coupler and 3 electrical connectors frees the burner assembly. Slid the old igniter out and the new one in.2 philips screws to remove the coil retainer and replace the coils.

The new rotary knob just popped right in. No problems. It was a perfect fit.

I disassembled the dryer using instructions from the following website for White Westinghouse (pictures really helped)
After removing the drum, I first noticed that the grouding ball was sitting on the bottom of the dryer (along with much lint). I then saw that the bracket for bearing support cup and the bearing support cup were both worn well past use. The bracket had been worn down about 1/4" to the SE with matching wear on the bearing support cup. There was a hole in the bottom of the bearing support cup (hence the grouding ball on the floor of dryer).
I installed the new idler pulley assembly and completely vacuumed out the dryer (I didn't know lint could get so stiff!). I installed the new parts from the kit once received (and the new belt bought previously) and the dryer works great. I'm so used to the obnoxious squealing that it seems odd to be so quiet.

The internet is a magnificent thing!