GSG746RFS2 Gibson Dryer - Overview

Sections of the GSG746RFS2

[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
Rear Drum Bearing Kit – Part Number: 5303281153
Rear Drum Bearing Kit
★★★★★
★★★★★
(104)
PartSelect #: PS459829
Manufacturer #: 5303281153
This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will not tumble, or if i...
$62.31
  In Stock
Drum Belt – Part Number: 134503600
Drum Belt
★★★★★
★★★★★
(55)
PartSelect #: PS1148434
Manufacturer #: 134503600
This drum belt, often referred to as a drive belt, is used in the assembly of dryers. It goes around the drum, the idler pulley, and the motor pulley. As the armature on the motor spins, this belt is ...
$17.64
  In Stock
Upper Drum Glide – Part Number: 5303937139
Upper Drum Glide
★★★★★
★★★★★
(29)
PartSelect #: PS470317
Manufacturer #: 5303937139
The upper drum glide is attached to the front panel of your dryer, you can locate it by removing the top portion of your dryer. The drum glide allows the drum to rotate with ease and little sound. The...
$34.77
  In Stock
Drum Support Bearing – Part Number: 131825900
Drum Support Bearing
★★★★★
★★★★★
(20)
PartSelect #: PS418807
Manufacturer #: 131825900
If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which a...
$6.32
  In Stock
Rotary Knob – Part Number: 131965300
Rotary Knob
★★★★★
★★★★★
(16)
PartSelect #: PS419092
Manufacturer #: 131965300
This knob accepts a D-shaped shaft. Sold individually.
$46.34
  In Stock
Front Lower Drum Seal – Part Number: 5303283286
Front Lower Drum Seal
★★★★★
★★★★★
(3)
PartSelect #: PS460194
Manufacturer #: 5303283286
The front lower drum seal is used in the assembly of dryers. This seal helps keep your appliance running quietly. It allows the drum to smoothly rotate on the front panel. If you notice brown marks on...
$33.80
  On Order
Door Catch – Part Number: 131658800
Door Catch
★★★★★
★★★★★
(19)
PartSelect #: PS418433
Manufacturer #: 131658800
The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, which allows the door...
$51.19
  In Stock
Turn - Type Start Switch – Part Number: 134398300
Turn - Type Start Switch
★★★★★
★★★★★
(14)
PartSelect #: PS975832
Manufacturer #: 134398300
This part is used to start the dryer once you have selected a setting on the timer.
$58.89
  In Stock
M Series Ignition Coil Kit – Part Number: 5303931775
M Series Ignition Coil Kit
★★★★★
★★★★★
(24)
PartSelect #: PS470049
Manufacturer #: 5303931775
This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the ...
$21.43
  In Stock
Dryer Drum Bearing Bracket – Part Number: 131724301
Dryer Drum Bearing Bracket
★★★★★
★★★★★
(2)
PartSelect #: PS12579101
Manufacturer #: 131724301
This drum bearing bracket is for dryers. Drum bearing bracket holds and supports the drum bearing
$10.65
  In Stock
Lint Filter – Part Number: 131450300
Lint Filter
★★★★★
★★★★★
(11)
PartSelect #: PS417841
Manufacturer #: 131450300
Located at the front of the dryer, this lint filter traps lint and debris from the exhaust air flowing out of the dryer drum. This part measures approximately 12 inches long x 7 inches high, has a pla...
$28.48
  In Stock
Door Strike – Part Number: 5303207102
Door Strike
★★★★★
★★★★★
(7)
PartSelect #: PS455020
Manufacturer #: 5303207102
The door strike is attached to the door of your dryer and holds the door closed. If your dryer door is not closing, this might be due to the door strike needing to be replaced. This is a simple repair...
$16.15
  In Stock

Questions And Answers for GSG746RFS2

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

1 question answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Corey
March 26, 2020
The drum won't kick start
For model number GSG746RFS2
PartSelect logo
Hello Corey, Thank you for the question. In most cases this is a caused by a worn or broken Belt, PartSelect Number PS1148434. There is a how to video on the site listed under the belt part number for accessing the belt. We hope this helps.

Was this helpful?
Thank you for voting!
Related Parts:
  • 1

Common Symptoms of the GSG746RFS2

[Viewing 7 of 7]
Noisy
Fixed by
these parts
Fixing Fixing Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing Fixing Fixing
Show All
Door won’t close
Fixed by
these parts
Fixing Fixing
Show All
Drum Not Spinning
Fixed by
these parts
Fixing Fixing
Show All
Not Heating
Fixed by
these parts
Fixing Fixing
Show All
Won’t Start
Fixed by
these parts
Fixing
Show All
Too hot
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Squealing noise
We followed the instructions for the drum glide replacement and changed the belt and drum support bearing piece, cleaned it out too. Works like a charm. Thanks for saving us a bundle.
Parts Used:
Drum Belt Upper Drum Glide Drum Support Bearing
  • Cynthia from Lexington, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Wrench (Adjustable), Wrench set
529 of 551 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud Squeaking
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Access panel at rear of dryer.
7.Unscrew 3 screws from inside, center rear of drum.
8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit
9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket)
10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer.
11. Vacuum everything--duct, blower, lint trap, ect.
12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside
13. reassemble remainder of parts in reverse order.
Parts Used:
Rear Drum Bearing Kit
  • Frank from Boyertown, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
334 of 353 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor would hum but not turn on when start knob was turned.
The motor bearings had stiffened up – classic planned obsolescence.

I could tell the motor was bad, because when I tried to spin the drum by hand, it wouldn't turn in any direction. (Normally it can turn fairly easily.)

(Helpful hint: As you remove screws / parts, place them in a plastic baggie, and write on the baggie from whence they came. This is especially helpful if you have to order parts and then wait a few days for them to arrive.)

You can replace the starter motor without removing the drum, but it is easier if you do remove the drum. Plus, I decided to also replace the drum belt, since it was 9 years old and is a wear part.

UNPLUG THE DRYER BEFORE YOU BEGIN.

1. Pop off the top cover; it has two spring clips at the front, then it hinges up. Disconnect the green grounding wire at the back, then slip the cover off the hinges and set it aside.

2. Remove the front panel:

a. Looking down into the dryer, disconnect the electrical harnesses that go between the front controls and the body. You may have to cut a nylon cable tie to access one or more. (Note that they have shapes that won't allow you to mix them up later). Also, there are two wires that attach to connectors in the top middle of the dryer, which are difficult to get at; you may need a needle nose pliers to pull them. Remember their color-coding for reinstallation.

b. Remove the two phillips screws located about 8 inches from the top, on either side, inside the body, that hold the front panel in place.

c. The front panel is now held in place by spring clips. Pry it gently to pop it loose. It will hinge out, then you can pull it up. Notice how the front piece has felt pads that serve to hold the front of the drum; you'll line it up the same way when it goes back together. Set the front panel aside.

3. Remove the rear motor vent plate.
a. It is at the back, lower right of the dryer (which is lower left once you're behind it). 2 phillips screws hold it in place.

b. Now look inside to see the motor and belt. Memorize how the belt feeds around the motor pulley and the larger, white plastic tensioner pulley. Notice how the rear motor bearing sits in a half-round metal plate, held down by a spring clip. (Make a drawing if you like.)

c. Move the spring- loaded tensioner arm to take tension off the belt, then slip the belt off the motor pulley.

d. Notice that the tensioner pulley, arm and spring are all held in place by the spring. Note that the tensioner pulley can slip off its shaft. Note these things for when you put it all back together later.

e. Now undo the tensioner arm spring and remove the arm, pulley and spring. Set them aside.


4. Remove the drum:

a. There is a yellowish plastic block at the top front of the open dryer body that holds the drum. Take it out with a phillips screwdriver.

b. Slip the now un-tensioned belt off the drum, to the back, so it hangs over the heater element body. You can leave it there for now, so you don't forget to install it before you put everything back together. If you're going to replace the belt, now is a good time to do so. (Check the length of the new belt against the old one, to make sure they're the same.)

c. Now you can remove the drum. It uses a center ball in a socket joint at the back to hold it in place. Use a screwdriver to lever upward on the back of the drum. This will pop the ball up, and then you can pull the drum out from the front.

5. Clean it up.
Now is a very good time to vacuum out any lint in the fan area, inside the dryer body, etc. Also consider removing the lint trap assembly from the dryer front ( 2 phillips screws) and vacuuming it out as well.

6. Remove the motor.

a. First, remove the fan that's attached to the front of the motor. Use a socket (7/8", I think) to unscrew the fan from the front of the motor shaft. IMPORTANT: The fan has a plastic hex nut sh
Parts Used:
Drum Belt Drive Motor with Pulley
  • Elvis from Miami, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
213 of 248 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!