GS395LEGB1 Whirlpool Range - Instructions

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.

Had to remove the bottom oven shelf and the broiler drawer. Disconnected the wiring pigtail theought the broiler opening and pulled the gas pipe from the baking oven. Reomved the two screws connecting the ignitor from the pipe. Connected the new ignitor and threaded the wiring pigtail back down the the opening in the baking oven. Connected the wiring harness up inside the broiler and put the drawer back in. Re-installed the bottom shelf in the baking oven and tested. Worked perfectly. Back to cooking. :-)

We removed with a screwdriver the two main screws that held the bottom of the oven in place and removed the bottom oven piece; then we removed the two nuts with a socket wrench that held the element in place. We then discovered that the element wire did not completely egress to the point of being able to disconnect from within the oven, so we removed the storage drawer below the oven and that provided access to disconnect the element wire and reconnect the new element wire and then reverse the steps to install the new element, which worked fine upon first use and continues to work fine.

Oven is gas. Burners on top OK, broiler in oven OK. Removed oven bottom plate and heat deflector. Carborundum igniter would not glow. Ordered new igniter from Partselect.com. With new igniter in hand I unplugged the oven from house power, removed the bottom drawer for access to the igniter connector, and disconnected it. Removed the bad igniter and replaced with new igniter...easy! Plugged in oven to house power and tested new igniter by turning on oven. GOOD!! Reassemmbled oven interior. Wife again happy.

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes

Called repair man and described the problem. He said I could do it myself. PartSelect had the part and a previous description on the PartSelect site told me how to do the repair. It was easy. Be careful when removing the igniter nuts. I used a very small amount of sewing machine oil so as not to strip the threads. works great.

The repair went well. Only took a few minutes. Oven is 21 years old and still working. I figured why throw away if still working. Thank you Select Parts for coming to my rescue. Will keep you in mind.

Only one screwdriver needed for this simple repair. Unfortunately for me it did not repair my oven and a new code on the oven indicated a bigger problem with computer board.
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!

Was super easy even I could do it. Wish I would have done it 2 years ago when my husband broke it. Just used a Phillips screwdriver. Very easy!

I slid the range out about 8 inches from the wall, and having unplugged the range and looked at the diagram from the Parts Select site, I used a mirror and screwdriver to remove the screws holding the small rear cover. From there I removed the one screw holding the spark module and that way I was able to hold the old and new one side by side to move the wires. Reversed the process, easy peasy.

1st gen whirlpool Duet dryer sensor not working in automatic cycle.
After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of a pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.

DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.