GLGR341AS0 Frigidaire Dryer - Instructions

Removed old knob and tension band from shaft. Pushed new knob into place

Just fit right in.

Main problem was the bearing, replaced the belt and felt seal as well
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again

followed the instructions video on the site had no problems just took about 2 hrs to complete

After unplugging the dryer, disconnecting it from the vent, and moving into an open work area, I popped the top open with the blade of a screwdriver, disconnected the two wires that connect to the door switch, then lifted the front panel (with the door) up and away from the drum. Next, I lifted the drum out of the worn rear bearing assembly and lowered it into the dryer in order to release tension on the belt. I then removed the entire drum by carrying it forward and out of the way. I then removed the old bearing assembly, which was loose and covered with metal dust. After cleaning the area with a dry cloth to remove the old grease and metal dust, and vacuuming all the lint off *everything*, I installed the new bearing assembly with a 5/16" nut driver, being careful to position the provided ball-bearing between the plastic bearing assembly and the outer clip. The little ball-bearing is very important, as it is the drum's only path to ground, and prevents the build up of static electricity as the drums spins. I then filled the new bearing assembly with the provided grease. Everything is easy up to this point, but the difficult part for me was removing the old hub from the drum and re-attaching the new one. It is held on by three screws and they become seated very tightly. After loosening them and removing the old hub from the drum, attaching the new one prvoed difficult as well, as the screw-holes in the new hub are not threaded to fit the screws. The screws muct be forced to cut a thread as you install them, which requires a great deal of force. After installing the new hub and putting the new belt (pruchased separately) around the drum, the next step is to reinstall the drum by lifting it in through the front of the dryer and positioning the new hub over the new bearing assembly and pressing it down into place. It will gently "snap" into place as it seats. Then, on the back side of the dryer, I removed the vent panel by removing the two screws that hold it in place and positioned the new drive belt (loosely dangling around the drum) over the motor's drive wheel and behind the sring-tensioned idle arm. Then it is a simply matter to reinstall the front panel by genly lifting the drum and sliding the door opening inside it, then reseating all the little clips that hold the front panel in place. I then pressed the top back into place, reconnected the vent hose, plugged it back in and checked for operation. My fifteen year-old dryer now works like new!

Once I found this site, with everybody's description of the problem & fix, it was pretty easy.
Pry the front of the top up using a flat screwdriver at each side. Then disconnected the dryer-controls wire bundle (dryer unplugged of course) at the connector, and unscrewed 1 screw on each side of the front panel close to the top (under the controls, back-side of the panel), in order to pry the front panel off - top 1st.
With everything opened up, just unscrew the two screws on top of the burner coil. the pull off the plate, slip off the 2 coils, disconnect the wires, and install the new coils in reverse. Put it all back together and you're good!
(I replaced the drum glides too, while I was in there - just in time!)

The conversion kit had everything needed, However the instructions were lacking in description on how to assemble everything, this kit includes the new style burner, igniter, igniter mount, air shutter and propane orifices. A detailed picture would help.
The hot surface igniter was broken in the box, luckily the dryer had the same style igniter already installed. I just had to reposition the original igniter to light properly. No special tools needed. Read the instructions before installing.

There was a lot of screws. And I cleaned everything well. The one part was bad so I replaced them all to make sure it'll last.

remove old knob and washer that was on it put new knob on and turn the knob dryer was save

watched you tube video... a breeze

Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!

Took apart the dryer, definitely a two person job. Cleaned up a bag full of lint that collected in the dryer (can't believe it didn't start a fire!), removed the old glides and seals, sandpapered off the old adhesive, applied fresh adhesive, attached the glide and seals, waited for the adhesive to dry, reassembled the dryer. Now it's working like a charm!

Romoved front from dryer . Then loosened tub , slid belt on , reached in back and put belt on pulley , turned tub till belt went into place and reassembled dryer all with the help of a 3 year old and an8 year old,so in my oppinion it was one of the easiest fixes i've ever done!

Remove top panel with large flat screwdriver and 2 screws in back.Remove bottom panel with 2 screws.Release belt tensioner and remove belt.Remove 3 screws in center of drum inside.Remove drum. Remove rear bearing by pulling up on assembly.Replace all parts in reverse order.

The appliance is gas, which made me a little nervous. However, knowing that I had the gas off, I carefully began disassembly. The burner unit is a very simple set up and within a few minutes I had the entire assembly out and noticed that in fact the igniter was broken. I ordered a new one from partselect.com and it was delivered in 2 days! The worst part of the assembly was when I accidentally bumped the new igniter against the underside of the dryer and broke the brand new one!!!..So, I ordered a second igniter and 2 days later installed it in about 30 minutes.