All Installation Instructions for General Electric Dishwasher GLD4458R10CS

Detergent cap would not stay closed

After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.

Parts Used:

Detergent Dispenser with Rinse Cap

Michelle from Carlisle, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

one wheel was missing, others kept on falling off

Just snapped studs and wheels together and put them into place.

Parts Used:

Single Lower Wheel Stud/Axle

Lower Rack Wheel Kit - 8 Pack

ILONA from AUSTIN, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

We had a rip in our tub gasket.

I removed the old seal, cleaned behind it, and then put the new seal in. We saw a video on You Tube on how to do it. Partselect also sent instructions on a e mail with the order receipt. We enjoyed working with you guys. Your customer service representative was very nice and accurate in sending out the part. All went as she said it would. Thanks!!

Parts Used:

Tub Gasket

Estelle from Queen Creek, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

axle for wheel was broken

Popped the axle on to the wheel, then snapped it on to the lower drawer - done!

Parts Used:

Single Lower Wheel Stud/Axle

Gail from Woodstock, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

missing toekick

two screws, two minutes, all done

Parts Used:

TOEKICK Assembly

KENNETH from WAPPINGERS FALLS, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Leaking valve

Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.

Parts Used:

Water Inlet Valve

Gary from HAVERHILL, MA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Roller Broken on dishwasher

Popped out Old Roller, put in new one, pushing it together with a pair of pliers.

My only regret is that i didn't check the other side of the dishwasher... the other roller was broken also, and now i have to pay 5.95 shipping & handling for a .29 cent item

Check all your rollers before you buy just one!!!!!

Parts Used:

Dishwasher Dishrack Rollers and Axles

Sean from Cicero, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

upper dishwashr rack lost the end cap and the rack kept coming off the track when you went to push it back in it would jam into the track and all the dishes would bang and fall.

placed the end cap into location and forced it into place. Fixed -and we are all much happier!!

Parts Used:

Dishwasher Rack Slide End Cap

donna from walworth, NY
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

The door on dishwasher soap dispenser broke.

Repaired the soap dispenser.

Parts Used:

Detergent Dispenser with Rinse Cap

Eric from SIMPSONVILLE, SC
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Old soap dispensor latch would not hold

Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.

Parts Used:

Detergent Dispenser with Rinse Cap