GH4155XPS3 Whirlpool Microwave - Instructions

used screw driver to pry up old part. lifted right off. line up drive couple drive push on. repair took less than 1 minute to repair. works like new
Very Pleased with Parts Select replacement parts

Whirlpool Model# MH1150XMS-0 purchased in 2004. I called Whirlpool and they suggested a new microwave. No big surprise - being the thrifty person that I am I wasn’t taking this for an answer. I figured if I had to purchase a new microwave what was $35.22 (part# PS373828 + shipping) if it worked.

I replaced the latch on the microwave door. Once the latch was replaced. I also took this time to make sure that the microwave door was in alignment. Thereafter, I had to adjust the door interlock switch behind the microwave console panel to recognize the microwave being closed. Yes, gaining access to all these areas was a bit difficult but have patience. TADA!!!....microwave is working. #girlsrock

It took me 15 minutes total - 5 minutes to clean the microwave, 1 minute to install three new parts, and 9 minutes to enjoy my celebratory glass of wine!

After taking the three screws out of the side of the door, I actually had to get help from my Dad who came over and was able to pry the top corner of the door out of the casing. I was afraid I was going to break the door. Once he got the door pried apart, I was able to replace the handle, clean the entire door and quickly snap it back into place and then replaced the screws.

both of the pieces have a tab that help remove the pieces. They slip right out and new ones are putin place.

It's a simple repair but costly. Just open the door remove the three screws on the side of door. Now use a small screw driver or metal putty knife to remove the chooker collar around the door " be careful this can easly be broken". Okay now the metal inner door is easier to remove if you slightly bend the tabs up around the door. Look carefully you should be able to see where they catch. Once you do that carefully seperate the outter door cover. Careful sometimes it will pop right out and fall. Please no more further repairs needed. Just screw in the new handle push tabs back out on the metal inner door then snap everything back together and reinstall the three screws.

removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on the other side.

Opened door and put new plate in.

Placed order on Thursday evening and received Sat Am

Took out 2 phillips screws on top, pulled the old grill out, hooked the tabs on the bottom of the replacement into place, positioned the top of the replacement, and replaced the 2 screws. 5 minutes. NOTE: Save the screws, new ones don't come with the replacement grill.

Took out turntable and swapped out old one with a new bright and shiny
New one, ring that is. It was easy using the part from parts select
Thanks
Paul

It took me time to remove the parts and suss out the issue, but the repair itself was EASY. A wire ribbon connected to the circuit board had gone bad. One Phillips head screwdriver, 7 screws, to get at the old one, pull it out, replace it with the newly ordered part. NO PROBLEM. Ladies, you can do IT!! You have the power!

After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)

The most difficult part was getting the old screw out of the top of the grille. Once that was accomplished, the rest was easy as can be. I would highly recommend your service - very good! Thank you!

Took out the turntable parts to ensure I ordered the correct cooking tray. Matching those with photos of related parts on PartSelect worked great. Put turntable drive and support ring in place and cooking tray went in very easily. Plan to order a second one to have on hand for this rental property.

My vent grill fer me microwave done and fell off.