GDWT768V55SS General Electric Dishwasher - Instructions

I repaired by replacing both inner rails.
I found that removing an inner rail from the rack is difficult. It can be done with strong fingers separating the tabs of a front Y hook after releasing the rear hook so the rack can slide off the horizontal locator rods. It helps to apply liquid soap to the old inner rails Y clips to reduce friction.
Clean the outer rails thoroughly with a brush and liquid cleaner so the rails can engage
Inserting the inner rails into the outer rails is difficult when they are already attached to the rack. It's much easier to insert the rails independently of the rack. Push the outer rails into the inner rails while applying force to keep them engaged

Attach the rack to the rails by inserting the long rear horizontal rods of the rack into the rear clips of the rail.
Assure the tabs in the rear clips are locked
Again, it helps to apply liquid soap to the new inner rail Y clips to reduce friction
Hold the rails in place and pull the rack forward to engage the front rails with Y clips to the shorter front horizontal rods of the rack.
Force them together to spread the Y clips and lock the rails into them.

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish washer, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.

Removed dishwasher from under counter. Removed both cable pulleys and bushings. Threaded new cables and remounted pulleys and bushings. Finally stretched springs onto cables. Checked counter balance and reinstalled dishwasher.

The noise came from the dishwasher door. Removed the Phillips screws from the door edge to gain access by separating the front of the door. Had to disconnect some of the electrical connectors to allow more access. Disconnected the blower motor connector. Removed the screws holding the motor assembly and removed the blower motor. Installed the new blower motor and reconnected the electrical connectors. Reassembled the door and cycled the dishwasher. Very quiet now!

Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.

shut off water. removed lower panel disconnected power removed supply hose and outlet hose. disconnected electrical plug from valve. Un bolted valve from frame. removed elbow from valve inlet. installed elbow on new valve using Teflon tape. reinstalled valve to frame. connect hoses + electric plug to new valve. turn water on check for leaks. reconnect power. run dish washer check for leaks & popper operation. reinstall lower panel.

Simply pull out the old axle and snap in the new one. It is simple. Also the replacement axels were MUCH better quality than the originals. The bottom tray now slides in and out very easily. Note, if you have this problem, you do not need to replace the wheel, just the axle.

but axle on new wheen and put axle on tray

Really all it took was removal of the old wheels which would not stay on anyway and the installation of the new ones. That required the axle and wheel being put together and the installing both of those on the lower rack. I was about to buy a new dishwasher when the salesmen told me about a product called Lemi Shine it saved my hundreds of dollars and the inside of my dishwasher looks brand new. With my new wheels I am good to go again.

I simply removed the old (broken) stud rollers by pinching them with a needle nose pliers and pushing them out, snapped the new stud roller in the wheel, and snapped the wheel onto the lower basket unit. If you have all of the wheels and they are in good shape, you do not need to buy new wheels, the new stud rollers work just fine with the old wheels.

This was a simple part swap. The stud rollers are the small peg-clips that hold the wheel on the lower dish rack. Removing the old stud rollers from the wheels required a pair of pliers. I then popped the new stud rollers into the old wheels and snapped them back onto the lower dish rack. I scored some major points from my frustrated wife -- easy, fast fix!

Pull out the old, died gasket. Clean out track that holds gasket. insert new gasket.

Removed the existing stud rollers with the wheels attached. Then removed the wheels from the stud roller. Then snapped the wheels on the new "Better Designed" stud rollers. Then easily snapped the new stud roller assembly in place. Piece of cake...works like a charm.

Thanks,

Randy

Removed empty basket from dishwasher. Placed basket upside down and removed remaining wheels from basket by detaching worn axel from attachment points. ie, No tools needed for this procedure. Once axel and wheels were removed, I squeezed the end of the old axel with needle nose pliers or regular pliers to relieve the outward pressure and pushed the old axel out of the wheels. Easy, popped right out.
Positioned new axel against the outer wheeel hole and applied thumb/finger pressure to snap in new axel. Took the wheel with the new axel and
attached it to the basket at the original position. New axel grips the basket like a clothes pin would.
Continued and replaced all eight axels at this time.
Replace basket in machine, stand back and admire work and parts!!!! Parts received promptly with no hassels. Excellent company to do business with, clear photos and ordering forms.
Will definately re order again if needed. Thank You.