GDF650SSJ4SS General Electric Dishwasher - Instructions

Unplugged power.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.

READ THE INSTRUCTIONS THAT COME WITH THE PART! After taking the dishwasher apart and installing the new part...it still didn't work. Then we read the instructions that came with the part. There are different settings on the part depending on your model of dishwasher. We removed the part, set it to our dishwasher, and it works perfectly. The job could have been quicker if the instructions had been read first.

Followed a u-tube video to remove dish wash door assembly to get to the control board . Not too hard if you are mechanically inclined.

After reading the manual that came with my dishwasher, 5 years ago, it states if the green LED is on steady, change the machine control board. PartsSelect sent the bd within a week. I replace the board but the result was the same (steady green LED); Contacting PartsSelect, they gave me a return label and shipped another control board. Unfortunately the second control board had the same outcome. PartsSelect send another return label and I returned both machine control boards. I contacted GE and am having a service man (from GE) come and fix it. The manual for this dishwasher must be in error!! PartsSelect has been fantastic in understanding this and allowing me to return the bds.

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

the design of this part is easy to break when closing the top rack.

there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher

the part broke when closing the rack [a dish too tall hit it]

it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel

My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine

Twist counter clockwise to remove clockwise to install

Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!

Make sure power to dishwasher is off. Unscrew from counter. Pull dishwasher out enough to expose pulleys that hold the door in place. Remove lower panel and insulation. Unplug door jack from main panel underneath. Loosen pulleys on each side and remove door. Take a 1/4 in socket and remove the bolt on the upper side of the hook on each side, then remove the screws on the outer side panel on each side. Now slide the inner door panel up (push the top and pull the bottom), which will release the hooks on each side. Turn over the inner panel and remove the four screws that hold the interface control panel in place. Unplug the two jacks and remove the panel. Now take a small flat-head screwdriver to remove the clear cover. Remove the control panel. Make sure you set the junction as prescribed with the instructions that come with the new control panel. MIND YOU- YOU HAVE TO REMOVE THE JUNCTIONS (TAKE EACH ONE OUT) AND RESET THEM ON THE PRONGS IN THE ORDER AS PRESCRIBED. Replace the control panel, replace the clear cover, insert it back in place, plug in jacks and replace screws. Turn inner panel over and line up side where the hooks lock. replace all screws and bolts. Replace door on dishwasher, plug in jack to main panel, attach pulleys to door. Replace insulation and front panel to bottom of dishwasher. Push dishwasher back in place. Replace screws that hold dishwasher to counter. Turn main power back on and VOILA!!

This is a replacement that is straightforward but a bit mechanical. For an experienced engineer it was no problem but for the common household this is a repair best left to the pros. Fixed the issue no problem and the dishwasher is working perfectly now.

1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked

Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...

Repair was straightforward. You can change water inlet on this model from underneath in bottom from, although it is a little tight

Took cover of door off. Removeddoor from frame 1st. Lift door off of hinge. Disconnect door from springs. Unscrew bottom screws at base of door. Lift front cover(actually slides down) remove old part replace with new.make sure unplug door from main body.